Linux kernel 2.0.35 and Intep EEPro 10+/100B/100+
Nikica Petrinic
nikica.petrinic@eng.ox.ac.uk
Fri Sep 25 10:37:36 1998
Dear Donald,
I would appreciate if you could help.
We have a Dell PowerEdge 2300 with Intel Ether Express Pro 10+/100B/100+
network card (82557 chip) which refuses to work properly with RedHat v5.1.
When I booted from the RedHat v5.1 boot floppy in order to
download and install RedHat it all worked well (so I thought).
I successfully installed everything and rebooted. The network card
didn't pick-up. I turned the machine off and on again and the
network was there again. I checked if there was a hardware problem
with the network card by booting DOS and using Intel's utility
software to probe the card. It was reported OK.
I upgraded kernel to 2.0.35 (RedHat official updates) and made sure I
selected the right driver (make xconfig). Recompiled. Rebooted.
No sign of life from the network card. Turned the machine off and
on - nothing.
Is our network card supported at all? According to RedHat's Web page
it doesn't look like it. However, make xconfig clearly lists Intel Ether
Express Pro 10+/100B/100+ under supported PCI network cards.
Thanks.
Nik
P.S.
Here is what I found in /proc/pci /var/log/dmesg and by typing ifconfig
The only thing I spotted is the broadcast address it is 163.1.9.255 and
it should be 163.1.9.254. I tried setting it manually. It didn't help.
/proc/pci
------------------------------------------------------------
PCI devices found:
Bus 0, device 14, function 0:
Ethernet controller: Intel 82557 (rev 2).
Medium devsel. Fast back-to-back capable. IRQ 10. Master Capable. Latency=32. Min Gnt=8.Max Lat=56.
Prefetchable 32 bit memory at 0xf6000000.
I/O at 0xe4e0.
Non-prefetchable 32 bit memory at 0xfe000000.
Bus 0, device 8, function 1:
SCSI storage controller: Adaptec AIC-7895U (rev 3).
Medium devsel. Fast back-to-back capable. IRQ 11. Master Capable. Latency=32. Min Gnt=8.Max Lat=8.
I/O at 0xe800.
Non-prefetchable 32 bit memory at 0xfe100000.
Bus 0, device 8, function 0:
SCSI storage controller: Adaptec AIC-7895U (rev 3).
Medium devsel. Fast back-to-back capable. IRQ 14. Master Capable. Latency=32. Min Gnt=8.Max Lat=8.
I/O at 0xec00.
Non-prefetchable 32 bit memory at 0xfe101000.
Bus 0, device 7, function 3:
Bridge: Intel 82371AB PIIX4 ACPI (rev 2).
Medium devsel. Fast back-to-back capable.
Bus 0, device 7, function 2:
USB Controller: Intel 82371AB PIIX4 USB (rev 1).
Medium devsel. Fast back-to-back capable. Master Capable. Latency=64.
I/O at 0x0.
Bus 0, device 7, function 1:
IDE interface: Intel 82371AB PIIX4 IDE (rev 1).
Medium devsel. Fast back-to-back capable. Master Capable. Latency=64.
I/O at 0xffa0.
Bus 0, device 7, function 0:
ISA bridge: Intel 82371AB PIIX4 ISA (rev 2).
Medium devsel. Fast back-to-back capable. Master Capable. No bursts.
Bus 0, device 2, function 0:
PCI bridge: DEC DC21152 (rev 3).
Medium devsel. Fast back-to-back capable. Master Capable. Latency=32. Min Gnt=2.Max Lat=3.
Bus 1, device 0, function 0:
VGA compatible controller: ATI Mach64 GD (Rage Pro) (rev 92).
Medium devsel. Fast back-to-back capable. IRQ 255. Master Capable. Latency=32. Min Gnt=8.
Non-prefetchable 32 bit memory at 0xfc000000.
I/O at 0xfc00.
Non-prefetchable 32 bit memory at 0xfbfff000.
Bus 0, device 1, function 0:
PCI bridge: Intel 440BX - 82443BX AGP (rev 2).
Medium devsel. Master Capable. Latency=32. Min Gnt=136.
Bus 0, device 0, function 0:
Host bridge: Intel 440BX - 82443BX Host (rev 2).
Medium devsel. Master Capable. Latency=32.
Prefetchable 32 bit memory at 0xf0000000.
------------------------------------------------------------
/var/log/dmesg
------------------------------------------------------------
mpted
aic7xxx: during machine bootup.
aic7xxx: Cables present (Int-50 NO, Ext-50 NO)
aic7xxx: Termination Enabled
(scsi0) <Adaptec AIC-7895 Ultra SCSI host adapter> found at PCI 8/0
(scsi0) Wide Channel A, SCSI ID=7, 32/255 SCBs
(scsi0) BIOS enabled, IO Port 0xec00, IRQ 14
(scsi0) IO Memory at 0xfe101000, MMAP Memory at 0x4807000
(scsi0) Resetting channel A
(scsi0) Downloading sequencer code... 413 instructions downloaded
(scsi1) <Adaptec AIC-7895 Ultra SCSI host adapter> found at PCI 8/1
(scsi1) Narrow Channel B, SCSI ID=7, 32/255 SCBs
(scsi1) BIOS enabled, IO Port 0xe800, IRQ 11
(scsi1) IO Memory at 0xfe100000, MMAP Memory at 0x4809000
(scsi1) Resetting channel B
(scsi1) Downloading sequencer code... 413 instructions downloaded
ppa: Version 1.42
ppa: Probing port 03bc
ppa: Probing port 0278
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.0.19/3.2.4
<Adaptec AIC-7895 Ultra SCSI host adapter>
scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.0.19/3.2.4
<Adaptec AIC-7895 Ultra SCSI host adapter>
scsi : 2 hosts.
(scsi0:0:-1:-1) Scanning channel for devices.
Vendor: SEAGATE Model: ST39102LC Rev: 0004
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: SEAGATE Model: ST39102LC Rev: 0004
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
Vendor: SEAGATE Model: ST39102LC Rev: 0004
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdc at scsi0, channel 0, id 2, lun 0
Vendor: SEAGATE Model: ST39102LC Rev: 0004
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdd at scsi0, channel 0, id 3, lun 0
Vendor: NEC Model: CD-ROM DRIVE:465 Rev: 1.03
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 5, lun 0
(scsi1:0:-1:-1) Scanning channel for devices.
scsi : detected 1 SCSI cdrom 4 SCSI disks total.
(scsi0:0:0:0) Using wide (16 bit) transfers.
(scsi0:0:0:0) Synchronous at 20.0MHz, offset 8.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 17783240 [8683 MB] [8.7 GB]
(scsi0:0:1:0) Using wide (16 bit) transfers.
(scsi0:0:1:0) Synchronous at 20.0MHz, offset 8.
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 17783240 [8683 MB] [8.7 GB]
(scsi0:0:2:0) Using wide (16 bit) transfers.
(scsi0:0:2:0) Synchronous at 20.0MHz, offset 8.
SCSI device sdc: hdwr sector= 512 bytes. Sectors= 17783240 [8683 MB] [8.7 GB]
(scsi0:0:3:0) Using wide (16 bit) transfers.
(scsi0:0:3:0) Synchronous at 20.0MHz, offset 8.
SCSI device sdd: hdwr sector= 512 bytes. Sectors= 17783240 [8683 MB] [8.7 GB]
eepro100.c:v0.99B 4/7/98 Donald Becker linux-eepro100@cesdis.gsfc.nasa.gov
eth0: Intel EtherExpress Pro 10/100 at 0xe4e0, 00:A0:C9:C7:32:6A, IRQ 10.
Board assembly 704666-002, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x49caa8d6).
Receiver lock-up workaround activated.
eepro100.c:v0.99B 4/7/98 Donald Becker linux-eepro100@cesdis.gsfc.nasa.gov
Partition check:
sda: sda1 sda2 < sda5 sda6 sda7 >
sdb: sdb1 sdb2 < sdb5 sdb6 >
sdc: sdc1 sdc2 < sdc5 sdc6 >
sdd: sdd1 sdd2 < sdd5 sdd6 >
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 128484k swap-space (priority -1)
Adding Swap: 128484k swap-space (priority -2)
Adding Swap: 128484k swap-space (priority -3)
Adding Swap: 128484k swap-space (priority -4)
Adding Swap: 128484k swap-space (priority -5)
Adding Swap: 128484k swap-space (priority -6)
Adding Swap: 128484k swap-space (priority -7)
Adding Swap: 128484k swap-space (priority -8)
------------------------------------------------------------
ifconfig
------------------------------------------------------------
lo Link encap:Local Loopback
inet addr:127.0.0.1 Bcast:127.255.255.255 Mask:255.0.0.0
UP BROADCAST LOOPBACK RUNNING MTU:3584 Metric:1
RX packets:10439 errors:0 dropped:0 overruns:0
TX packets:10439 errors:0 dropped:0 overruns:0
eth0 Link encap:Ethernet HWaddr 00:A0:C9:C7:32:6A
inet addr:163.1.9.124 Bcast:163.1.9.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:4 dropped:0 overruns:0
TX packets:315 errors:0 dropped:0 overruns:315
Interrupt:10 Base address:0xe4e0
------------------------------------------------------------
------------------------------------------------------------------------
Nikica Petrinic
University Technology Centre for Solid Mechanics
Department of Engineering Science
University of Oxford
Engineering & Technology Building
Parks Road
Oxford OX1 3PJ
Tel +44 (0)1865 273813, 273811, 273812
Fax +44 (0)1865 273906
E-mail nikica.petrinic@eng.ox.ac.uk
------------------------------------------------------------------------