[eepro100] two i82559 on board do not work
Anton Yurchenko
phila@dg.net.ua
Wed Sep 25 06:00:01 2002
Hello,
I have a Tyan LE-T Dual CPU motherboard
(http://www.tyan.com/products/html/thunderlet.html), it is based on
ServerWorks III LE3 chipset, with two i82559 controllers.
I`m running RedHat 7.3, uname -a:
--------------------------------------------------------------------------------
Linux typhoon.dg 2.4.18-10smp #1 SMP Wed Aug 7 11:17:48 EDT 2002 i686 unknown
--------------------------------------------------------------------------------
The first controller is working fine, but when I try to initialize the
second one I get such msgs(this is the ethernet initialization part):
--------------------------------------------------------------------------------
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg>
and others
eth0: Intel Corp. 82557/8/9 [Ethernet Pro 100], 00:E0:81:21:03:DC, IRQ 20.
Board assembly 567812-052, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
eth1: Intel Corp. 82557/8/9 [Ethernet Pro 100] (#2), 00:E0:81:21:03:DD, IRQ 21.
Board assembly 567812-052, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
Self test failed, status ffffffff:
Failure to initialize the i82557.
Verify that the card is a bus-master capable slot.
eepro100: wait_for_cmd_done timeout!
eepro100: wait_for_cmd_done timeout!
... [ about 40 of such ]
eepro100: wait_for_cmd_done timeout!
--------------------------------------------------------------------------------
and the card doesnt work.
I tryed fiddling with BIOS but no luck. PnP OS option in BIOS is disabled, BIOS shows one controller
on IRQ 10, and the other on IRQ 11.
I dont have anything besides
--------------------------------------------------------------------------------
alias eth0 eepro100
alias eth1 eepro100
--------------------------------------------------------------------------------
in my modules.conf
Here is some diagnostics from eepro100-diag:
--------------------------------------------------------------------------------
eepro100-diag.c:v2.08 4/17/2002 Donald Becker (becker@scyld.com)
http://www.scyld.com/diag/index.html
Index #1: Found a Intel i82557/8/9 EtherExpressPro100 adapter at 0xd400.
EEPROM contents, size 64x16:
00: e000 2181 dc03 0403 0000 0201 4701 0000
0x08: 5678 1234 40a0 100c 8086 0000 0000 0000
...
0x30: 0128 0000 0000 0000 0000 0000 0000 0000
0x38: 0000 0000 0000 0000 0000 0000 0000 552b
The EEPROM checksum is correct.
Intel EtherExpress Pro 10/100 EEPROM contents:
Station address 00:E0:81:21:03:DC.
Board assembly 567812-052, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
Index #2: Found a Intel i82557/8/9 EtherExpressPro100 adapter at 0xd000.
EEPROM contents, size 64x16:
00: e000 2181 dd03 0403 0000 0201 4701 0000
0x08: 5678 1234 40a0 100c 8086 0000 0000 0000
...
0x30: 0128 0000 0000 0000 0000 0000 0000 0000
0x38: 0000 0000 0000 0000 0000 0000 0000 542b
The EEPROM checksum is correct.
Intel EtherExpress Pro 10/100 EEPROM contents:
Station address 00:E0:81:21:03:DD.
Board assembly 567812-052, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
--------------------------------------------------------------------------------
And here are the /proc/interupts, /proc/ioports, first for the kernel booted without APIC
(noapic option), and then with APIC:
--------------------------------------------------------------------------------
CPU0 CPU1
0: 198754 0 XT-PIC timer
1: 1838 0 XT-PIC keyboard
2: 0 0 XT-PIC cascade
8: 1 0 XT-PIC rtc
10: 0 0 XT-PIC eth1
11: 1549 0 XT-PIC eth0
14: 13062 0 XT-PIC ide0
15: 14 0 XT-PIC ide1
NMI: 0 0
LOC: 198680 198679
ERR: 0
MIS: 0
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
d000-d03f : Intel Corp. 82557/8/9 [Ethernet Pro 100] (#2)
d000-d03f : eepro100
d400-d43f : Intel Corp. 82557/8/9 [Ethernet Pro 100]
d400-d43f : eepro100
d800-d8ff : ATI Technologies Inc Rage XL
ffa0-ffaf : ServerWorks OSB4 IDE Controller
ffa0-ffa7 : ide0
ffa8-ffaf : ide1
--------------------------------------------------------------------------------
CPU0 CPU1
0: 8003 12658 IO-APIC-edge timer
1: 2 0 IO-APIC-edge keyboard
2: 0 0 XT-PIC cascade
8: 1 0 IO-APIC-edge rtc
14: 5274 5440 IO-APIC-edge ide0
15: 2 15 IO-APIC-edge ide1
20: 240 306 IO-APIC-level eth0
21: 0 0 IO-APIC-level eth1
NMI: 0 0
LOC: 20577 20575
ERR: 0
MIS: 0
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
d000-d03f : Intel Corp. 82557/8/9 [Ethernet Pro 100] (#2)
d000-d03f : eepro100
d400-d43f : Intel Corp. 82557/8/9 [Ethernet Pro 100]
d400-d43f : eepro100
d800-d8ff : ATI Technologies Inc Rage XL
ffa0-ffaf : ServerWorks OSB4 IDE Controller
ffa0-ffa7 : ide0
ffa8-ffaf : ide1
--------------------------------------------------------------------------------
Any help will be much appreciated.
Thnx,
--
Anton Yurchenko<phila@dg.net.ua>
Digital Generation