[eepro100] Entire 82801BA/BAM/CA/CAM system locks
Antonios Christofides
anthony at itia.ntua.gr
Mon May 17 14:19:53 PDT 2004
Hi,
I've installed Debian testing on an Acer Aspire 1400 Laptop, which
appears to have a NIC integrated with the motherboard,
82801BA/BAM/CA/CAM. The kernel is Debian precompiled 2.6.5-1-686, but
I've also tried 2.4.26-1-686 and I get the same symptoms. The NIC
generally works, but if there is much traffic the entire system freezes;
there is no response from the keyboard and mouse, and it does not reply
to pings. (e100 also works, but worse than eepro100, and it also
freezes the system. Booting with acpi=off or noapic does not improve
things. The system is dual-boot and it doesn't show any such problem
when it runs the other operating system.)
If there is only one connection, there is usually no problem. For
example, I installed the entire system from the network, and the first
time it hanged was probably when it tried to adjust the clock with nntp.
I've also downloaded a 1.5 GB file with http with no problem. The most
reliable way to freeze it is to mount an NFS system and do a find on it;
it usually freezes within 5 seconds. Sometimes I'm luckier and the
system doesn't freeze, but the NIC stops responding and I get
wait_for_cmd_done in the logs; I then restart the network and it works
again.
Searching the net I've found one or two people who've successfully
installed Linux on the same laptop, and there are no reports of any
problems. They just say "eepro100 works nicely".
I've read the archives and I understand that it may be hard to avoid
wait_for_cmd_done, but do you think I might at least avoid the freezing?
I include lots of information from my system below; lspci,
/proc/interrupts, /proc/ioports, dmesg, and an extract from syslog.
Thanks!
lspci
-----
0000:00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge (rev 04)
0000:00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge (rev 04)
0000:00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB/ER Hub interface to PCI Bridge (rev 05)
0000:00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 05)
0000:00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 05)
0000:00:1f.2 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #1) (rev 05)
0000:00:1f.3 SMBus: Intel Corp. 82801BA/BAM SMBus (rev 05)
0000:00:1f.4 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #2) (rev 05)
0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801BA/BAM AC'97 Audio (rev 05)
0000:00:1f.6 Modem: Intel Corp. Intel 537 [82801BA/BAM AC'97 Modem] (rev 05)
0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY
0000:02:00.0 CardBus bridge: O2 Micro, Inc. OZ6933 Cardbus Controller (rev 01)
0000:02:00.1 CardBus bridge: O2 Micro, Inc. OZ6933 Cardbus Controller (rev 01)
0000:02:08.0 Ethernet controller: Intel Corp. 82801BA/BAM/CA/CAM Ethernet Controller (rev 03)
cat /proc/interrupts
--------------------
CPU0
0: 2992846 XT-PIC timer
1: 9982 XT-PIC i8042
2: 0 XT-PIC cascade
5: 5 XT-PIC uhci_hcd, yenta
8: 4 XT-PIC rtc
9: 2735 XT-PIC acpi
11: 3727 XT-PIC Intel 82801BA-ICH2, uhci_hcd, eth0, yenta
12: 34833 XT-PIC i8042
14: 10705 XT-PIC ide0
15: 0 XT-PIC ide1
NMI: 0
LOC: 0
ERR: 0
MIS: 0
cat /proc/ioports
-----------------
0000-001f : dma1
0020-0021 : pic1
0040-005f : timer
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
04d0-04d1 : pnp 00:0a
0cf8-0cff : PCI conf1
1000-105f : pnp 00:0a
1060-107f : pnp 00:0a
1180-11bf : pnp 00:0a
1800-180f : 0000:00:1f.1
1800-1807 : ide0
1808-180f : ide1
1810-181f : 0000:00:1f.3
1820-183f : 0000:00:1f.2
1820-183f : uhci_hcd
1840-185f : 0000:00:1f.4
1840-185f : uhci_hcd
1880-18bf : 0000:00:1f.5
1880-18bf : Intel 82801BA-ICH2 - Controller
1c00-1cff : 0000:00:1f.5
1c00-1cff : Intel 82801BA-ICH2 - AC'97
2000-207f : 0000:00:1f.6
2400-24ff : 0000:00:1f.6
3000-3fff : PCI Bus #01
3000-30ff : 0000:01:00.0
4000-403f : 0000:02:08.0
4000-403f : eepro100
4400-44ff : PCI CardBus #03
4800-48ff : PCI CardBus #03
4c00-4cff : PCI CardBus #07
5000-50ff : PCI CardBus #07
dmesg
-----
Linux version 2.6.5-1-686 (herbert at gondolin) (gcc version 3.3.3 (Debian 20040401)) #5 Fri Apr 30 20:26:13 EST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 00000000000e0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fef0000 (usable)
BIOS-e820: 000000000fef0000 - 000000000feff000 (ACPI data)
BIOS-e820: 000000000feff000 - 000000000ff00000 (ACPI NVS)
BIOS-e820: 000000000ff00000 - 000000000ff80000 (usable)
BIOS-e820: 000000000ff80000 - 0000000010000000 (reserved)
BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
On node 0 totalpages: 65408
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61312 pages, LIFO batch:14
HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v000 TOSCPL ) @ 0x000f6db0
ACPI: RSDT (v001 TOSCPL RSDT 0x06040000 LTP 0x00000000) @ 0x0fefacc1
ACPI: FADT (v001 TOSCPL BR20 0x06040000 PTL 0x00000001) @ 0x0fefef64
ACPI: BOOT (v001 TOSCPL $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x0fefefd8
ACPI: DSDT (v001 COMPAL BR20 0x06040000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
Built 1 zonelists
Kernel command line: BOOT_IMAGE=Linux ro root=303
No local APIC present or hardware disabled
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 1994.175 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Memory: 251252k/261632k available (1521k kernel code, 9588k reserved, 633k data, 144k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3948.54 BogoMIPS
Security Scaffold v1.0.0 initialized
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4464k freed
CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebf9ff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: bfebf9ff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU#0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU#0: Thermal monitoring enabled
CPU: Intel(R) Pentium(R) 4 CPU 2.00GHz stepping 07
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd9a0, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Edge set to Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SLOT._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *5)
ACPI: PCI Interrupt Link [LNKB] (IRQs *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs *5)
ACPI: PCI Interrupt Link [LNKE] (IRQs *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 5)
ACPI: Embedded Controller [EC0] (gpe 28)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f6e10
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x9cc9, dseg 0x400
pnp: 00:0a: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0a: ioport range 0x1000-0x105f has been reserved
pnp: 00:0a: ioport range 0x1060-0x107f has been reserved
pnp: 00:0a: ioport range 0x1180-0x11bf has been reserved
PnPBIOS: 18 nodes reported by PnP BIOS; 18 recorded by driver
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
Simple Boot Flag at 0x36 set to 0x1
VFS: Disk quotas dquot_6.5.1
devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
atkbd.c: Unknown key pressed (raw set 0, code 0x17e on isa0060/serio2).
atkbd.c: Use 'setkeycodes 7e <keycode>' to make it known.
serio: i8042 AUX2 port at 0x60,0x64 irq 12
atkbd.c: Unknown key pressed (raw set 0, code 0x17e on isa0060/serio3).
atkbd.c: Use 'setkeycodes 7e <keycode>' to make it known.
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4464 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 144k freed
NET: Registered protocol family 1
SCSI subsystem initialized
libata version 1.02 loaded.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2: IDE controller at PCI slot 0000:00:1f.1
ICH2: chipset revision 5
ICH2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1800-0x1807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1808-0x180f, BIOS settings: hdc:DMA, hdd:pio
hda: IC25N020ATCS04-0, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: DW-224E, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 39070080 sectors (20003 MB) w/1768KiB Cache, CHS=38760/16/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 979956k swap on /dev/hda2. Priority:-1 extents:1
EXT3 FS on hda3, internal journal
Real Time Clock Driver v1.12
NET: Registered protocol family 17
cpufreq: P4/Xeon(TM) CPU On-Demand Clock Modulation available
input: PS/2 Generic Mouse on isa0060/serio4
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
drivers/usb/core/usb.c: registered new driver usbmouse
drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
mice: PS/2 mouse device common for all mice
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm at uk.sistina.com
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49496 usecs
intel8x0: clocking to 48000
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:1f.2: Intel Corp. 82801BA/BAM USB (Hub #1)
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: irq 5, io base 00001820
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:1f.4: Intel Corp. 82801BA/BAM USB (Hub #2)
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: irq 11, io base 00001840
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw at saw.sw.com.sg> and others
eth0: 0000:02:08.0, 00:02:3F:B3:36:C5, IRQ 11.
Board assembly 000000-000, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
ACPI: Battery Slot [BAT1] (battery present)
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Processor [CPU0] (supports C1 C2)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
Yenta: CardBus bridge found at 0000:02:00.0 [1025:0019]
Yenta: ISA IRQ mask 0x0498, PCI irq 5
Socket status: 30000006
Yenta: CardBus bridge found at 0000:02:00.1 [1025:0019]
Yenta: ISA IRQ mask 0x0498, PCI irq 11
Socket status: 30000006
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x20f 0x378-0x37f 0x3c0-0x3df
cs: IO port probe 0x0a00-0x0aff: clean.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02ef860(lo)
IPv6 over IPv4 tunneling driver
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
[drm] Initialized radeon 1.9.0 20020828 on minor 0
[drm:radeon_cp_init] *ERROR* radeon_cp_init called without lock held
[drm:radeon_unlock] *ERROR* Process 880 using kernel context 0
eth0: no IPv6 routers present
A wait_for_cmd_done example from syslog
---------------------------------------
May 17 19:07:33 meteolaptop kernel: eth0: wait_for_cmd_done timeout!
May 17 19:07:35 meteolaptop last message repeated 2 times
(Note: the following is probably me restarting the network)
May 17 19:08:00 meteolaptop laptop-net: Stopping network interface "eth0"
May 17 19:08:01 meteolaptop kernel: eth0: wait_for_cmd_done timeout!
May 17 19:08:01 meteolaptop kernel: eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html
May 17 19:08:01 meteolaptop kernel: eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw at saw.sw.com.sg> and others
May 17 19:08:01 meteolaptop kernel: eth0: 0000:02:08.0, 00:02:3F:B3:36:C5, IRQ 11.
May 17 19:08:01 meteolaptop kernel: Board assembly 000000-000, Physical connectors present: RJ45
May 17 19:08:01 meteolaptop kernel: Primary interface chip i82555 PHY #1.
May 17 19:08:01 meteolaptop kernel: General self-test: passed.
May 17 19:08:01 meteolaptop kernel: Serial sub-system self-test: passed.
May 17 19:08:01 meteolaptop kernel: Internal registers self-test: passed.
May 17 19:08:01 meteolaptop kernel: ROM checksum self-test: passed (0x04f4518b).
May 17 19:08:01 meteolaptop ifd[1637]: starting
May 17 19:08:01 meteolaptop ifd[1637]: executing: '/usr/share/laptop-net/link-change eth0 managed unknown up,running,connected'
May 17 19:08:01 meteolaptop ifd: PID file written: /var/run/ifd.pid
May 17 19:08:01 meteolaptop laptop-net: Network scheme "home" selected for "eth0" by "arp-discovery".
May 17 19:08:01 meteolaptop laptop-net: Starting network interface "eth0"
May 17 19:08:11 meteolaptop kernel: eth0: no IPv6 routers present
More information about the eepro100
mailing list