[eepro100] suspended and overruns
Joe Radinger
cheese at phion.com
Fri Sep 3 06:18:50 PDT 2004
do overruns occur when the card is not able to fullfill its duty and
some queue is filling up?
the affected ip is no longer responsive and connections break.
any ideas?
yours
josef
attached is some diag-output
-------------- next part --------------
Thu Sep 2 06:34:00 UTC 2004
---
eepro100-diag-output -ee -f
---
eepro100-diag.c:v2.02 7/19/2000 Donald Becker (becker at scyld.com)
http://www.scyld.com/diag/index.html
Index #1: Found a Intel i82557 (or i82558) EtherExpressPro100B adapter at 0xa000.
EEPROM contents, size 64x16:
00: 0200 a9b3 b3a3 040f ffff 0201 4701 ffff
0x08: a568 3102 5882 1015 8086 0064 ffff ffff
0x10: ffff ffff ffff ffff ffff ffff ffff ffff
0x18: ffff ffff ffff ffff ffff ffff ffff ffff
0x20: ffff ffff ffff 1229 ffff ffff ffff ffff
0x28: ffff ffff ffff ffff ffff ffff ffff ffff
0x30: 002c ffff ffff ffff ffff ffff ffff ffff
0x38: ffff ffff ffff ffff ffff ffff ffff 3c44
The EEPROM checksum is correct.
Intel EtherExpress Pro 10/100 EEPROM contents:
Station address 00:02:B3:A9:A3:B3.
Board assembly a56831-002, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
Secondary interface chip i82555, PHY -1.
Index #2: Found a Intel i82557 (or i82558) EtherExpressPro100B adapter at 0xa400.
EEPROM contents, size 64x16:
00: 0200 a9b3 b4a3 040f ffff 0201 4701 ffff
0x08: a568 3102 5882 1015 8086 0064 ffff ffff
0x10: ffff ffff ffff ffff ffff ffff ffff ffff
0x18: ffff ffff ffff ffff ffff ffff ffff ffff
0x20: ffff ffff ffff 1229 ffff ffff ffff ffff
0x28: ffff ffff ffff ffff ffff ffff ffff ffff
0x30: 002c ffff ffff ffff ffff ffff ffff ffff
0x38: ffff ffff ffff ffff ffff ffff ffff 3b44
The EEPROM checksum is correct.
Intel EtherExpress Pro 10/100 EEPROM contents:
Station address 00:02:B3:A9:A3:B4.
Board assembly a56831-002, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
Secondary interface chip i82555, PHY -1.
---
eepro100-diag-output -af
---
eepro100-diag.c:v2.02 7/19/2000 Donald Becker (becker at scyld.com)
http://www.scyld.com/diag/index.html
Index #1: Found a Intel i82557 (or i82558) EtherExpressPro100B adapter at 0xa000.
i82557 chip registers at 0xa000:
00000000 00000000 00000000 00080002 14202100 00000000
No interrupt sources are pending.
The transmit unit state is 'Idle'.
The receive unit state is 'Idle'.
This status is unusual for an activated interface.
Index #2: Found a Intel i82557 (or i82558) EtherExpressPro100B adapter at 0xa400.
i82557 chip registers at 0xa400:
0c006050 058747c0 00000000 00080002 1821780d 00000600
Interrupt sources are pending.
The transmit unit state is 'Suspended'.
The receive unit state is 'Ready'.
This status is unusual for an activated interface.
The Command register has an unprocessed command 0c00(?!).
---
mii-diag -vv
---
Using the default interface 'eth0'.
mii-diag.c:v2.00 4/19/2000 Donald Becker (becker at scyld.com)
http://www.scyld.com/diag/index.html
MII PHY #1 transceiver registers:
2100 7809 02a8 0154 05e1 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
0203 0000 0001 0000 0000 0000 0000 0000
0000 0000 0000 0000 0010 0000 0000 0000.
Basic mode control register 0x2100: Auto-negotiation disabled, with
Speed fixed at 100 mbps, full-duplex.
Basic mode status register 0x7809 ... 7809.
Link status: not established.
This transceiver is capable of 100baseTx-FD 100baseTx 10baseT-FD 10baseT.
Able to perform Auto-negotiation, negotiation not complete.
Link partner information information is not exchanged when in fixed speed mode.
MII PHY #1 transceiver registers:
2100 7809 02a8 0154 05e1 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
0203 0000 0001 0000 0000 0000 0000 0000
0000 0000 0000 0000 0010 0000 0000 0000.
Basic mode control register 0x2100: Auto-negotiation disabled!
Speed fixed at 100 mbps, full-duplex.
Basic mode status register 0x7809 ... 7809.
Link status: not established.
Capable of 100baseTx-FD 100baseTx 10baseT-FD 10baseT.
Able to perform Auto-negotiation, negotiation not complete.
Vendor ID is 00:aa:00:--:--:--, model 21 rev. 4.
No specific information is known about this transceiver type.
I'm advertising 05e1: Flow-control 100baseTx-FD 100baseTx 10baseT-FD 10baseT
Advertising no additional info pages.
IEEE 802.3 CSMA/CD protocol.
Link partner capability is 0000:.
Negotiation did not complete.
---
dmesg-output
---
: 0 pages.
IBM machine detected. Enabling interrupts during APM calls.
Kernel command line: auto BOOT_IMAGE=phion ro root=806
Initializing CPU#0
Detected 1266.684 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2529.68 BogoMIPS
Memory: 125044k/131008k available (1598k kernel code, 5576k reserved, 1324k data, 132k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU: Intel(R) Pentium(R) III CPU family 1266MHz stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch at atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfb2f0, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0686] at 00:07.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
JFFS version 1.0, (C) 1999, 2000 Axis Communications AB
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
parport_pc: Via 686A parallel port disabled in BIOS
pty: 2048 Unix98 ptys configured
Serial driver version 5.05d (2002-10-11) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:DMA, hdd:pio
hdc: LG CD-ROM CRD-8484B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: attached ide-cdrom driver.
hdc: ATAPI 48X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
ide-floppy driver 0.99.newide
ide-floppy driver 0.99.newide
NFTL driver: nftlcore.c $Revision: 1.87 $, nftlmount.c $Revision: 1.31 $
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus]
Intel PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
host/usb-uhci.c: $Revision: 1.275 $ time 08:35:30 Nov 2 2003
host/usb-uhci.c: High bandwidth mode enabled
host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech at suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
802.1Q VLAN Support v1.8 Ben Greear <greearb at candelatech.com>
All bugs added by David S. Miller <davem at redhat.com>
ds: no socket drivers loaded!
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 588k freed
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
PCI: Found IRQ 11 for device 00:0a.0
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.8
<Adaptec 29160B Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
blk: queue c7e92018, I/O limit 4095Mb (mask 0xffffffff)
Vendor: IBM-ESXS Model: ST318305LW !# Rev: B244
Type: Direct-Access ANSI SCSI revision: 03
blk: queue c7e92218, I/O limit 4095Mb (mask 0xffffffff)
scsi0:A:0:0: Tagged Queuing enabled. Depth 253
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:A:0): 160.000MB/s transfers (80.000MHz DT, offset 63, 16bit)
SCSI device sda: 35548320 512-byte hdwr sectors (18201 MB)
Partition check:
sda: sda1 sda2 < sda5 sda6 sda7 >
Freeing unused kernel memory: 132k freed
Adding Swap: 136512k swap-space (priority -1)
(scsi0:A:0:0): Locking max tag count at 64
divert: not allocating divert_blk for non-ethernet device pqd0
Madge Token Ring Linux Driver v2.41
Copyright (c) 1999 Madge Networks Ltd
divert: not allocating divert_blk for non-ethernet device tr0
tr0: Madge Presto PCI 2000 Adapter at b800 IRQ 5 PCI Bus 0 DevFn 48
tr0: BIA: 0040811A1BAC Force Ring Speed: 16 MBit/s
tr0: Tx Slots: 4 Rx Slots: 16 MaxFrameLen: 2040
divert: not allocating divert_blk for non-ethernet device tr1
tr1: Madge Presto PCI 2000 Adapter at c400 IRQ 10 PCI Bus 0 DevFn 78
tr1: BIA: 0040811A1B87 Force Ring Speed: 16 MBit/s
tr1: Tx Slots: 4 Rx Slots: 16 MaxFrameLen: 2040
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw at saw.sw.com.sg> and others
divert: allocating divert_blk for eth0
eth0: Intel Corp. 82557/8/9 [Ethernet Pro 100], 00:02:B3:A9:A3:B3, IRQ 11.
Board assembly a56831-002, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
Secondary interface chip i82555.
Forcing 100Mbs full-duplex operation.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0xb874c1d3).
divert: allocating divert_blk for eth1
eth1: Intel Corp. 82557/8/9 [Ethernet Pro 100] (#2), 00:02:B3:A9:A3:B4, IRQ 10.
Board assembly a56831-002, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
Secondary interface chip i82555.
Forcing 10Mbs half-duplex operation.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0xb874c1d3).
tr0: The adapter has opened in classic mode at 16 MBit/s
tr1: The adapter has opened in classic mode at 16 MBit/s
controld uses obsolete (PF_INET,SOCK_PACKET)
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out: status f048 0c00 at 12499338/12499398 command 000ca000.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out: status e050 0c00 at 12499398/12499458 command 0001a000.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out: status e050 0c00 at 12499458/12499518 command 0001a000.
---
lspci -v
---
00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
Flags: bus master, medium devsel, latency 8
Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Capabilities: [c0] Power Management version 2
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: d4000000-d6ffffff
Capabilities: [80] Power Management version 2
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: [c0] Power Management version 2
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT8235 Bus Master ATA133/100/66/33 IDE
Flags: bus master, medium devsel, latency 32
I/O ports at c000 [size=16]
Capabilities: [c0] Power Management version 2
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Flags: medium devsel, IRQ 9
Capabilities: [68] Power Management version 2
00:09.0 Token ring network controller: Madge Networks Smart 16/4 PCI Ringnode Mk3 (rev 02)
Subsystem: Madge Networks Presto PCI Plus Adapter
Flags: bus master, medium devsel, latency 32, IRQ 5
I/O ports at b800 [size=128]
Memory at d8100000 (32-bit, non-prefetchable) [size=128]
Capabilities: [f8] Power Management version 1
00:0a.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
Subsystem: Adaptec 29160LP Low Profile Ultra160 SCSI Controller
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 11
BIST result: 00
I/O ports at bc00 [disabled] [size=256]
Memory at d8101000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
00:0e.0 PCI bridge: Intel Corp. 21154 PCI-to-PCI Bridge (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 32
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: d8000000-d80fffff
Capabilities: [dc] Power Management version 1
00:0f.0 Token ring network controller: Madge Networks Smart 16/4 PCI Ringnode Mk3 (rev 02)
Subsystem: Madge Networks Presto PCI Plus Adapter
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at c400 [size=128]
Memory at d8102000 (32-bit, non-prefetchable) [size=128]
Capabilities: [f8] Power Management version 1
01:00.0 VGA compatible controller: ATI Technologies Inc Rage XL AGP 2X (rev 27) (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc: Unknown device 8008
Flags: bus master, stepping, medium devsel, latency 32, IRQ 7
Memory at d4000000 (32-bit, non-prefetchable) [size=16M]
I/O ports at 9000 [size=256]
Memory at d6000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [50] AGP version 1.0
Capabilities: [5c] Power Management version 2
02:04.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 0d)
Subsystem: Intel Corp. EtherExpress PRO/100 S Dual Port Server Adapter
Flags: bus master, medium devsel, latency 32, IRQ 11
Memory at d8041000 (32-bit, non-prefetchable) [size=4K]
I/O ports at a000 [size=64]
Memory at d8000000 (32-bit, non-prefetchable) [size=128K]
Capabilities: [dc] Power Management version 2
02:05.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 0d)
Subsystem: Intel Corp. EtherExpress PRO/100 S Dual Port Server Adapter
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at d8040000 (32-bit, non-prefetchable) [size=4K]
I/O ports at a400 [size=64]
Memory at d8020000 (32-bit, non-prefetchable) [size=128K]
Capabilities: [dc] Power Management version 2
---
cat /proc/interrupts
---
CPU0
0: 438772952 XT-PIC timer
1: 10 XT-PIC keyboard
2: 0 XT-PIC cascade
5: 301983135 XT-PIC mtok
8: 1225 XT-PIC rtc
10: 55599087 XT-PIC mtok, eth1
11: 175666709 XT-PIC aic7xxx
15: 23 XT-PIC ide1
NMI: 0
ERR: 0
---
ifconfig
---
eth1 Link encap:Ethernet HWaddr 00:02:B3:A9:A3:B4
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:13227730 errors:0 dropped:0 overruns:0 frame:0
TX packets:12499502 errors:0 dropped:0 overruns:34 carrier:0
collisions:599 txqueuelen:100
Interrupt:10 Base address:0x3000
eth1:S009 Link encap:Ethernet HWaddr 00:02:B3:A9:A3:B4
inet addr:X.X.X.X Bcast:0.0.0.0 Mask:255.255.255.255
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:10 Base address:0x3000
lo Link encap:Local Loopback
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:32490629 errors:0 dropped:0 overruns:0 frame:0
TX packets:32490629 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
lo:loop Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.255.255.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
tap0 Link encap:Ethernet HWaddr FE:FD:00:00:00:00
UP BROADCAST RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
tap0:fw Link encap:Ethernet HWaddr FE:FD:00:00:00:00
inet addr:127.0.1.1 Bcast:127.0.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING NOARP MULTICAST MTU:1500 Metric:1
tap1 Link encap:Ethernet HWaddr FE:FD:00:00:00:00
UP BROADCAST RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
tap1:aux1 Link encap:Ethernet HWaddr FE:FD:00:00:00:00
inet addr:X.X.X.X Bcast:0.0.0.0 Mask:255.255.255.255
UP BROADCAST RUNNING NOARP MULTICAST MTU:1500 Metric:1
tap1:vpn Link encap:Ethernet HWaddr FE:FD:00:00:00:00
inet addr:127.0.2.1 Bcast:127.0.2.255 Mask:255.255.255.0
UP BROADCAST RUNNING NOARP MULTICAST MTU:1500 Metric:1
tap2 Link encap:Ethernet HWaddr FE:FD:00:00:00:00
UP BROADCAST RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
tap2:aux2 Link encap:Ethernet HWaddr FE:FD:00:00:00:00
inet addr:X.X.X.X Bcast:0.0.0.0 Mask:255.255.255.255
UP BROADCAST RUNNING NOARP MULTICAST MTU:1500 Metric:1
tap2:vpnp Link encap:Ethernet HWaddr FE:FD:00:00:00:00
inet addr:127.0.3.1 Bcast:127.0.3.255 Mask:255.255.255.0
UP BROADCAST RUNNING NOARP MULTICAST MTU:1500 Metric:1
tr0 Link encap:16/4 Mbps Token Ring (New) HWaddr 00:40:81:1A:1B:AC
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:145387830 errors:0 dropped:0 overruns:0 frame:0
TX packets:135408696 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
Interrupt:5 Base address:0xb800
tr0:S009f Link encap:16/4 Mbps Token Ring (New) HWaddr 00:40:81:1A:1B:AC
inet addr:10.248.0.132 Bcast:0.0.0.0 Mask:255.255.255.255
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:5 Base address:0xb800
tr0:mip0 Link encap:16/4 Mbps Token Ring (New) HWaddr 00:40:81:1A:1B:AC
inet addr:X.X.X.X Bcast:10.248.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:5 Base address:0xb800
tr0:net1 Link encap:16/4 Mbps Token Ring (New) HWaddr 00:40:81:1A:1B:AC
inet addr:X.X.X.X Bcast:10.248.0.135 Mask:255.255.255.248
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:5 Base address:0xb800
tr1 Link encap:16/4 Mbps Token Ring (New) HWaddr 00:40:81:1A:1B:87
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5711445 errors:0 dropped:0 overruns:0 frame:0
TX packets:3170642 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
Interrupt:10 Base address:0xc400
tr1:S009f Link encap:16/4 Mbps Token Ring (New) HWaddr 00:40:81:1A:1B:87
inet addr:X.X.X.X Bcast:0.0.0.0 Mask:255.255.255.255
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:10 Base address:0xc400
---
More information about the eepro100
mailing list