Sudden Timeout Error of RTL-8139 Card

[Shigeo Sagai]

I sent below content last night, and the network has hung again.
I took diagnosis while the network hung and replace the data of
diagnosis.


>Dear Sirs, 
>I'm using a WISECOM WS-R410, a RTL-8139 Fast Ethernet Card on my
>linux box(Kernel Version is 2.0.35 and the driver version is 1.00F).
>The machine is connected with a full-duplex 100Base-TX switching HUB.
>
>It seems to work very nice soon after booting. But after three of
>four hours, it suddenly dies leaving message on the console:
>
>eth0: Transmit timeout, status 0d 0000 media 00
>eth0: Tx queue starts entry 4 dirty entry 0
>
>The system doesn't hang up totally, only network ability dies.
>
>The time between booting and network hang varies and I can't understand
>what is happening.
>
>Could you kindly suggest me, how to fix this problem.
>
>I checked /proc/pci and it says:
>
>  Bus  0, device  13, function  0:
>    Ethernet controller: Realtek 8139 (rev 16).
>      Medium devsel.  IRQ 11.  Master Capable.  Latency=32.  Min Gnt=32.Max Lat=64.
>      I/O at 0xe800.
>      Non-prefetchable 32 bit memory at 0xe7001000.
>
>
>From dmesg:
>
>rtl8139.c:v1.00F 8/12/98 Donald Becker
>http://cesdis.gsfc.nasa.gov/linux/drivers/rtl8139.html
>eth0: RealTek RTL8139 Fast Ethernet at 0xe800, IRQ 11, 00:20:18:88:e6:a7.
>
>From Dianosis Program:
<replace the new data while hanging>

bash# ./rtl8139-diag -af
Found a RealTek PCI Ethernet RealTek RTL8129 card at 0xe800.
RealTek chip registers at 0xe800
 0x000: 88182000 0000a7e6 ffffffff ffffffff 00002000 00002000 00002000 00002000
 0x020: 07d88018 07d88618 07d88c18 07d89218 07d60018 0d000000 0000fff0 0000807f
 0x040: 60000400 00009c00 6f5b9356 00000000 006c10c6 00000000 01000040 00100000
 0x060: 1100000f 05e1782d 000141e1 00000000 00000024 000007c8 00000000 00000000.
  No interrupt sources are pending.
 The chip configuration is 0x10 0x6c, MII mode.

bash# ./rtl8139-diag -af
Found a RealTek PCI Ethernet RealTek RTL8129 card at 0xe800.
EEPROM contents:
  8129 10ec 8139 10ec 8139 4020 f3d0 2000
  8818 a7e6 2c10 0000 0000 0000 0000 0000
  0000 0000 0000 0000 0000 0000 0000 0000
  0000 0000 0000 0000 0000 0000 0000 0000
  0000 0000 0000 0000 0000 0000 0000 0000
  0000 0000 0000 0000 0000 0000 0000 0000
  ffff ffff ffff ffff ffff ffff ffff ffff
  ffff ffff ffff ffff ffff ffff ffff ffff
 The word-wide EEPROM checksum is 0x5561.
Parsing the EEPROM of a RealTek chip:
  PCI IDs -- Vendor 0x10ec, Device 0x8139, Subsystem 0x10ec.
  PCI timer settings -- minimum grant 32, maximum latency 64.
  General purpose pins --  direction 0xf3  value 0xd0.
  Station Address 00:20:18:88:E6:A7.
  Configuration register 0/1 -- 0x2c / 0x00.
 EEPROM active region checksum is 08c2.

>And I've got a RTL-8139 setting program from the realtek site.
>The setting program can set Rx enable/disable and Tx enable/disable.
>I can't understand what setting is correct for the linux driver.
>
>
>If any other detaild information is needed, please ask me.
>I would try to collect information as much as possible.

Thank you in advance.

P.S.
My tulip card works quite well and flawlessly with the same linux
box. I just wanted to use cheaper 10/100 network card to introduce
to other collegues...
--
----+----1----+----2----+----3----+----4----+----5----+----6----+
  Shigeo Sagai                       sagai@criepi.denken.or.jp   
 | To unsubscribe, send mail to Majordomo@cesdis.gsfc.nasa.gov, and within the
 |  body of the mail, include only the text:
 |   unsubscribe this-list-name youraddress@wherever.org
 | You will be unsubscribed as speedily as possible.