From gardner at networknow.org Mon Jun 7 12:17:23 2004 From: gardner at networknow.org (Gardner Pomper) Date: Tue Nov 9 01:14:28 2010 Subject: [scyld-users] newbie v29 install question In-Reply-To: <644D9337A02FC24689647BF9E48EC39E08ABB7DF@drm556> Message-ID: Hi, I am just installing Scyld v29 on the test cluster I am building. Currently, I have only the master node (Asus PC-DL Deluxe dual Xeon motherboard) with an extra LinkSys 10/100 ethernet card for off-cluster networking. Everything installed fine, but when I boot, it does not seem to activate the onboard Intel 82547EI Gigabit LAN controller. The Network Configuration application detects it as a 8254OEM Gigabit Ethernet Controller (LOM), with a status of 'ok' at eth1, but when I try to activate it, it says: Cannot activate network device eth1! tulip device eth1 does not seem to be present, delaying intialization It gives the same message on bootup, but it never does activate. Can someone give me some test to try? I have the network adapter plugget into a 10/100 switch (not managed) and the static IP address is set to 192.168.1.0 Thanks! - Gardner From Tryggvi.Edwald at CTBTO.ORG Wed Jun 9 12:55:06 2004 From: Tryggvi.Edwald at CTBTO.ORG (Tryggvi Edwald) Date: Tue Nov 9 01:14:28 2010 Subject: [scyld-users] Different support for OpenPBS in version 29 ? Message-ID: <20040609.195509.610449.DB861E442981A40AF79D13EF18A2A8E2@CTBTO.ORG> Hello, I have a small running cluster with version 28cz. My colleagues want to use an application that has been written for/with OpenPBS. Is there any difference in the support or behavior of OpenPBS on Scyld version 29 as compared to version 28 ? Tryggvi Edwald, Senior Software Engineer, Comprehensive Nuclear Test Ban Treaty Organization From pjgsmith at gmail.com Wed Jun 23 07:15:22 2004 From: pjgsmith at gmail.com (Phil Smith) Date: Tue Nov 9 01:14:28 2010 Subject: [scyld-users] Boot Problems: Intel 82540EM Gigabit Ethernet Controller Message-ID: <373498e70406230715559b7f98@mail.gmail.com> Hi all, I'm currently having problems setting up a Beowulf cluster and was hoping someone could lend me some help. The problem I'm having is with my nodes. I have 64 diskless nodes, and each is equipped wiht a Intel 82540EM Gigabit Ethernet Controller, however after installing the newest e1000 module from Intel and configuring the config.boot I receive the following error on all the nodes while attempting to phase 1 boot: Module install failed failed command insmod /modules/e1000 no usable network interfaces found I am fairly certain that the e1000 module is present and that the configuration is correct. Does anyone have any suggestions as to how I could debug/resolve such a problem? Any feedback would be greatly appreciated. Cheers, Phil Smith From pjgsmith at mail.student.cs.uwaterloo.ca Wed Jun 23 07:18:09 2004 From: pjgsmith at mail.student.cs.uwaterloo.ca (pjgsmith@mail.student.cs.uwaterloo.ca) Date: Tue Nov 9 01:14:28 2010 Subject: [scyld-users] Boot Problems: Intel 82540EM Gigabit Ethernet Controller Message-ID: <1088000289.40d99121803eb@www.nexusmail.uwaterloo.ca> Hi all, I'm currently having problems setting up a Beowulf cluster and was hoping someone could lend me some help. The problem I'm having is with my nodes. I have 64 diskless nodes, and each is equipped wiht a Intel 82540EM Gigabit Ethernet Controller, however after installing the newest e1000 module from Intel and configuring the config.boot I receive the following error on all the nodes while attempting to phase 1 boot: Module install failed failed command insmod /modules/e1000 no usable network interfaces found I am fairly certain that the e1000 module is present and that the configuration is correct. Does anyone have any suggestions as to how I could debug/resolve such a problem? Any feedback would be greatly appreciated. Cheers, Phil Smith ---------------------------------------- This mail sent through www.mywaterloo.ca