Problems with DS21143

[Martin Josko]

Hello,

I have problems getting my Digital DS21143 to work
(it works under DOS) Here ist the boot message:

tulip.c:v0.90 10/20/98 becker@cesdis.gsfc.nasa.gov
eth0: Digital DS21143 Tulip at 0xd800, 00 00 d1 1b fd 41, IRQ 9.
eth0:  EEPROM default media type Autosense.
eth0:  Index #0 - Media MII (#11) described by a 21142 MII PHY (3)
block.
eth0:  Index #1 - Media 10base2 (#1) described by a 21142 Serial PHY (2)
block.
eth0:  MII transceiver #1 config 3100 status 7849 advertising 0101.
eth0:  Advertising 01e1 on PHY 1, previously advertising 0101.
  PCI latency timer (CFLT) is unreasonably low at 0.  Setting to 64
clocks.
eth0: No link beat on the MII interface, status then 7849 now 7849.  


Here some outputs from tulip-diag:

tulip-diag.c:v1.07 2/10/99 Donald Becker (becker@cesdis.gsfc.nasa.gov)
Index #1: Found a Digital DS21143 Tulip adapter at 0xd800.
 Port selection is MII, half-duplex.
 Transmit started, Receive started, half-duplex.
  The Rx process state is 'Waiting for packets'.
  The Tx process state is 'Idle'.
  The transmit threshold is 128.
EEPROM transceiver/media description for the Digital DS21143 Tulip chip.

Leaf node at offset 40, default media type 0800 (Autosense).
 2 transceiver description blocks:
  Media MII, block type 3.
   MII interface PHY 0 (media type 11).
   21143 MII initialization sequence is 2 words: 0821 0000.
   21143 MII reset sequence is 3 words: 0821 0001 0000.
   Media capabilities are 7800, advertising 01e1.
   MII interrupt on GPIO pin -1.
 MII PHY found at address 1, status 0x7849.
 MII PHY #1 transceiver registers:
   3100 7849 2000 5c01 0101 0000 0000 0000
   0000 0000 0000 0000 0000 0000 0000 0000
   0000 0000 0000 0000 0000 0000 0001 8060
   8020 0c41 0000 3000 a3b9 0080 8005 001d.   

tulip-diag.c:v1.07 2/10/99 Donald Becker (becker@cesdis.gsfc.nasa.gov)
Index #1: Found a Digital DS21143 Tulip adapter at 0xd800.
Digital DS21143 Tulip Tulip chip registers at 0xd800:
  ffa04800 ffffffff ffffffff 00fff028 00fff228 f0660000 b20e2002
fbfffbff
  e0000000 ffffcbf8 ffffffff fffe0000 000000c6 ffff0000 fff80000
8ff40008
 Port selection is MII, half-duplex.
 Transmit started, Receive started, half-duplex.
  The Rx process state is 'Waiting for packets'.
  The Tx process state is 'Idle'.
  The transmit threshold is 128.  


Could somebody give me an hint ?

Regards

Martin


--
Martin Josko, Institut fuer Informatik der LMU    Tel.: +49/89/2178-2243
LFE Programmier- und Modellierungssprachen        FAX : +49/89/2178-2211
mailto:Martin.Josko@informatik.uni-muenchen.de          Oettingenstr. 67
http://www.informatik.uni-muenchen.de/~Martin.Josko     D-80538 Muenchen