DIGITAL PC 5500 21143 problems.
Karl Vogel
kvo@seagha.com
Fri Mar 19 04:12:35 1999
On Fri, 19 Mar 1999, Stephen Ashley wrote:
> I have posted this to the comp.os.linux.networking news group. Have
> not have any joy as to problem resolution.
>
> I have installed the 2.2.3 kernel source and rebuild my system kernel.
> Also used the new (24-feb-'99) tulip.c with the 2.2.3 source.
>
> I have found one other linux user within Compaq that has this problem.
> He as install a DEC DE450 (21041) base card. I have also done this, but
> due to a site restriction. I will have to remoce this card and go back
> to using the in-build controller chip.
I think I'm having the same problem as you.. somewhere around version
>0.79 my network card stopped working with the tulip driver. I found that
if I change the timer routine in the table at the start of the source,
from t21142_timer to tulip_timer, that my network card works again.
My /proc/pci entry is the same as yours (same chip revision).
Note: I know nothing about programming the DEC tulip chip, I just found
this out by comparing the working 0.79 driver with the newer (non-working)
driver.
I have reported this a few times in the past on this list.. never got any
comments about it ;-(
> Can anyone assit me in getting a resoulition to this problem. This
> problem is reproducable on all of these DEC PC modles I have tried on
> here.
>
> Cheers,
> Stephen Ashley,
> Alice Springs,
> Out Back Oz.
>
>
> +++++++++++++++++ Orignal Posting Below ++++++++++++++++++++++
> Subject:
> Tulip driver, with buildin 21143 controller.
> Date:
> Fri, 12 Mar 1999 13:03:24 +0930
> From:
> stephen ashley <stephen.ashley@compaq.com>
> Organization:
> compaq
> Newsgroups:
> comp.os.linux.networking, comp.os.linux.hardware
>
>
>
>
> I am having trouble getting and Digital PC 5000-266 PII system to use
> the build in DEC Chip 21143 ethernet controller. The onboard controller
> works fine, when I am in my BORG BODY SUIT (ie Windows NT4.0 SP4) But I
> am trying real hard to remove my BORG eye piece, Arm extender and body
> suit ;) .
>
> Anyhow enough of the sillyness. The red hat 5.2 CDrom install never
> detected this controller, I have re-build a(several) kernals (modular
> and monolitic) with the newest tulip.c (24-feb-'99). This kernal find
> the controller but end's up with a warning about the transcever being
> not found. When I tried a modular kernal I never saw the eth0: device
> get reported in the message log. I use the xconfig tool changed the 'Y'
> to a 'M' (PCI ether section was still 'Y') make boot; make clean; make
> dep; make modules; make modules_install. cpoy the kernel, and
> /sbin/lilo. Rebooted.
>
> Stephen Ashley,
> Member: ASLUG
> Alice Springs,
> Out Back Oz.
>
> Chip Markings.
> +++++++++++++++++++++++++++++++
> digital 21143-PB
> 21-44085-11
> (c)DEC 1996
> DC1071B
>
> /var/log/ Message file as below:--- Monlitic Kernel.
> +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
>
> Mar 12 09:39:30 ali49 kernel: The PCI BIOS has not enabled the device
> at 0/24! Updating PCI command 0014->0015.
> Mar 12 09:39:30 ali49 kernel: tulip.c:v0.90q 2/23/99
> becker@cesdis.gsfc.nasa.gov
> Mar 12 09:39:30 ali49 kernel: eth0: Digital DS21143 Tulip rev 48 at
> 0xec00, 00:00:F8:7A:00:13, IRQ 9.
> Mar 12 09:39:30 ali49 kernel: eth0: EEPROM default media type
> Autosense.
> Mar 12 09:39:30 ali49 kernel: eth0: Index #0 - Media 10baseT (#0)
> described by a 21142 Serial PHY (2) block.
> Mar 12 09:39:30 ali49 kernel: eth0: Index #1 - Media 10baseT-FD (#4)
> described by a 21142 Serial PHY (2) block.
> Mar 12 09:39:30 ali49 kernel: eth0: Index #2 - Media 10base2 (#1)
> described by a 21142 Serial PHY (2) block.
> Mar 12 09:39:30 ali49 kernel: eth0: Index #3 - Media AUI (#2) described
>
> by a 21142 Serial PHY (2) block.
> Mar 12 09:39:30 ali49 kernel: eth0: Index #4 - Media MII (#11)
> described by a 21142 MII PHY (3) block.
> Mar 12 09:39:30 ali49 kernel: eth0: ***WARNING***: No MII transceiver
> found!
> Mar 12 09:39:30 ali49 kernel: Partition check:
> Mar 12 09:39:30 ali49 kernel: sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
> Mar 12 09:39:30 ali49 kernel: sdb: sdb1
> Mar 12 09:39:30 ali49 kernel: VFS: Mounted root (ext2 filesystem)
> readonly.
> Mar 12 09:39:30 ali49 kernel: Adding Swap: 128484k swap-space (priority
> -1)
> Mar 12 09:39:30 ali49 kernel: Adding Swap: 128484k swap-space (priority
> -2)
> Mar 12 09:39:33 ali49 kernel: eth0: The transmitter stopped! CSR5 is
> f0068002, CSR6 b3860002.
> Mar 12 09:39:42 ali49 PAM_pwdb[338]: (login) session opened for user
> root by
> .
> .[SNIPED]
> .
> Mar 12 09:55:33 ali49 kernel: eth0: The transmitter stopped! CSR5 is
> f0008102, CSR6 b2420200.
> Mar 12 09:56:33 ali49 kernel: eth0: The transmitter stopped! CSR5 is
> f0008102, CSR6 b2420200.
> Mar 12 09:57:33 ali49 kernel: eth0: The transmitter stopped! CSR5 is
> f0008102, CSR6 b2420200.
> Mar 12 09:58:33 ali49 kernel: eth0: The transmitter stopped! CSR5 is
> f0008102, CSR6 b2420200.
> Mar 12 09:59:33 ali49 kernel: eth0: The transmitter stopped! CSR5 is
> f0008102, CSR6 b2420200.
>
> +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
>
> PCI Probe (/proc/pci)
> As Below:-
>
> PCI devices found:
> Bus 0, device 11, function 0:
> SCSI storage controller: Adaptec AIC-7881U (rev 0).
> Medium devsel. Fast back-to-back capable. IRQ 10. Master
> Capable. Latency=64. Min Gnt=8.Max Lat=8.
> I/O at 0xe800.
> Non-prefetchable 32 bit memory at 0xfdffa000.
> Bus 0, device 9, function 0:
> VGA compatible controller: Matrox Millennium (rev 1).
> Medium devsel. Fast back-to-back capable. IRQ 10.
> Non-prefetchable 32 bit memory at 0xfdffc000.
> Prefetchable 32 bit memory at 0xfd000000.
> Bus 0, device 7, function 1:
> IDE interface: Intel 82371SB PIIX3 IDE (rev 0).
> Medium devsel. Fast back-to-back capable. Master Capable.
> Latency=32.
> I/O at 0xecf0.
> Bus 0, device 7, function 0:
> ISA bridge: Intel 82371SB PIIX3 ISA (rev 1).
> Medium devsel. Fast back-to-back capable. Master Capable. No
> bursts.
> Bus 0, device 3, function 0:
> Ethernet controller: DEC DC21142 (rev 48).
> Medium devsel. Fast back-to-back capable. IRQ 9. Master
> Capable. Latency=165. Min Gnt=20.Max Lat=40.
> I/O at 0xec00.
> Non-prefetchable 32 bit memory at 0xfdffbc00.
> Bus 0, device 0, function 0:
> Host bridge: Intel 82441FX Natoma (rev 2).
> Medium devsel. Fast back-to-back capable. Master Capable.
> Latency=32.
> +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
>
>
>
>
>
>
>
>
.-----------------------------------------------------------------------------.
| SEAGHA cv. | Tel. ++32-(0)3232-2737 | Karl Vogel |
| Brouwersvliet 33, bus 8 | Fax. ++32-(0)3232-4526 | No junk mail please! |
| 2000 Antwerp, BELGIUM | URL. www.seagha.com | Karl.Vogel@seagha.com |
|-----------------------------------------------------------------------------|
| Opinions expressed herein are mine and not necessarily those of my employer |
`-----------------------------------------------------------------------------'