Trouble with DS21143 rev 65 (Sony Vaio Network Dock)
mbreuer@siac.com
mbreuer@siac.com
Tue Mar 30 14:33:04 1999
Hello,
If anyone can help...
I'm attempting to run linux (2.2.3) on a Sony Vaio PCG-808 w/ network
docking station. The docking station has a DS21143 chip (rev 65). I've
downloaded and installed the lastest tulip.c and can't seem to connect
to the network. I can ping the interface, but no other addresses. route
add commands fail (unable to connect to network). I've tried forcing the
transceiver choice to 10baseT (#0), to no avail. The machine has a
single RJ45 connector which is alleged by Windows to be 10/100.
According to the Sony specifications, it only supports 10baseT.
Attached is the output from tulip-diag, along with the list of PCI
devices & tulip syslog output.
Note: tulip-diag was run while the interface was up.
Any ideas?
Thanks in advance,
Michael Breuer
mbreuer@siac.com
PCI devices found:
Bus 0, device 0, function 0:
Host bridge: Intel 440BX - 82443BX Host (no AGP) (rev 2).
Medium devsel. Master Capable. Latency=64.
Prefetchable 32 bit memory at 0x4000000 [0x4000008].
Bus 0, device 7, function 0:
Bridge: Intel 82371AB PIIX4 ISA (rev 2).
Medium devsel. Fast back-to-back capable. Master Capable. No bursts.
Bus 0, device 7, function 1:
IDE interface: Intel 82371AB PIIX4 IDE (rev 1).
Medium devsel. Fast back-to-back capable. Master Capable. Latency=64.
I/O at 0xfcf0 [0xfcf1].
Bus 0, device 7, function 2:
USB Controller: Intel 82371AB PIIX4 USB (rev 1).
Medium devsel. Fast back-to-back capable. Master Capable. Latency=64.
I/O at 0xfcc0 [0xfcc1].
Bus 0, device 7, function 3:
Bridge: Intel 82371AB PIIX4 ACPI (rev 2).
Medium devsel. Fast back-to-back capable.
Bus 0, device 8, function 0:
VGA compatible controller: Neomagic Unknown device (rev 18).
Vendor id=10c8. Device id=5.
Medium devsel. Fast back-to-back capable. IRQ 9. Master Capable. Latency=128.
Min Gnt=16.Max Lat=255.
Prefetchable 32 bit memory at 0xfd000000 [0xfd000008].
Non-prefetchable 32 bit memory at 0xfe800000 [0xfe800000].
Non-prefetchable 32 bit memory at 0xfed00000 [0xfed00000].
Bus 0, device 10, function 0:
CardBus bridge: Ricoh Unknown device (rev 3).
Vendor id=1180. Device id=478.
Medium devsel. Master Capable. Latency=168. Min Gnt=128.Max Lat=7.
Bus 0, device 10, function 1:
CardBus bridge: Ricoh Unknown device (rev 3).
Vendor id=1180. Device id=478.
Medium devsel. Master Capable. Latency=168. Min Gnt=128.Max Lat=7.
Bus 0, device 16, function 0:
PCI bridge: Intel 82380FB Mobile (rev 1).
Slow devsel. Master Capable. No bursts. Min Gnt=4.
Bus 1, device 4, function 0:
IDE interface: CMD 646 (rev 5).
Medium devsel. Fast back-to-back capable. IRQ 9. Master Capable. Latency=64.
Min Gnt=2.Max Lat=4.
I/O at 0x1e8 [0x1e9].
I/O at 0x354 [0x355].
I/O at 0x160 [0x161].
I/O at 0x344 [0x345].
I/O at 0xecf0 [0xecf1].
Bus 1, device 8, function 0:
SCSI storage controller: Adaptec AIC-7860 (rev 3).
Medium devsel. Fast back-to-back capable. Master Capable. Latency=64. Min
Gnt=4.Max Lat=4.
I/O at 0x5800 [0x5801].
Bus 1, device 9, function 0:
Ethernet controller: DEC DC21142 (rev 65).
Medium devsel. Fast back-to-back capable. Master Capable. Latency=165. Min
Gnt=20.Max Lat=40.
I/O at 0xec00 [0xec01].
Non-prefetchable 32 bit memory at 0xfe7ff800 [0xfe7ff800].
Bus 1, device 10, function 0:
FireWire (IEEE 1394): Unknown vendor Unknown device (rev 1).
Vendor id=104d. Device id=8009.
Medium devsel. Master Capable. Latency=64.
Mar 22 17:22:37 mbreuer kernel: tulip.c:v0.90q 2/23/99 becker@cesdis.gsfc.nasa.gov
Mar 22 17:22:37 mbreuer kernel: eth0: Digital DS21143 Tulip rev 65 at 0xec00,
08:00:46:01:A9:5B, IRQ 0.
Mar 22 17:22:37 mbreuer kernel: eth0: EEPROM default media type Autosense.
Mar 22 17:22:37 mbreuer kernel: eth0: Index #0 - Media 10baseT (#0) described by a 21142
Serial PHY (2) block.
Mar 22 17:22:37 mbreuer kernel: eth0: Index #1 - Media 10base2 (#1) described by a 21142
Serial PHY (2) block.
Mar 22 17:22:37 mbreuer kernel: eth0: Index #2 - Media 10baseT-FD (#4) described by a
21142 Serial PHY (2) block.
Mar 22 17:22:37 mbreuer kernel: eth0: Index #3 - Media MII (#11) described by a 21142 MII
PHY (3) block.
Mar 22 17:22:37 mbreuer kernel: eth0: ***WARNING***: No MII transceiver found!
tulip-diag.c:v1.08 2/28/99 Donald Becker (becker@cesdis.gsfc.nasa.gov)
Index #1: Found a Digital DS21143 Tulip adapter at 0xec00.
Digital DS21143 Tulip Tulip chip registers at 0xec00:
f8000000 ffffffff ffffffff 00fab100 00faa040 f0000000 32040040 f3fe0000
e0000000 fff583ff ffffffff 00000000 000000c6 ffff0000 ffffffff 8ff70000
Port selection is MII, half-duplex.
Transmit stopped, Receive stopped, half-duplex.
The Rx process state is 'Stopped'.
The Tx process state is 'Stopped'.
The transmit threshold is 128.
EEPROM contents:
104d 801e 0000 0000 0000 0000 0000 0000
18c5 0104 0008 0146 5ba9 1e00 0000 0800
8604 0002 08ff 00f0 0286 ff01 f008 8600
0402 08ff 00f0 038d 0000 0000 e078 0001
0050 0018 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 7fac
0000 0000 0000 0008 0146 8398 0020 0000
0000 0000 0000 0000 0000 0000 0000 0635
ID CRC 0xc5 (vs. 0xc5), complete CRC 539f5722.
EEPROM transceiver/media description for the Digital DS21143 Tulip chip.
Leaf node at offset 30, default media type 0800 (Autosense).
4 transceiver description blocks:
Media 10baseT, block type 2.
Serial transceiver for 10baseT (media type 0).
GP pin direction 08ff GP pin data 00f0.
Media 10base2, block type 2.
Serial transceiver for 10base2 (media type 1).
GP pin direction 08ff GP pin data 00f0.
Media 10baseT-Full Duplex, block type 2.
Serial transceiver for 10baseT-Full Duplex (media type 4).
GP pin direction 08ff GP pin data 00f0.
Media MII, block type 3.
MII interface PHY 0 (media type 11).
21143 MII initialization sequence is 0 words:.
21143 MII reset sequence is 0 words:.
Media capabilities are 7800, advertising 01e1.
MII interrupt on GPIO pin -1.
21140 Non-MII transceiver with media 0 (10baseT).
CSR12 control port setting 00, command 00 00.
Media detection by looking for a 1 on bit 0 of the CSR12 control port.
21140 Non-MII transceiver with media 0 (10baseT).
CSR12 control port setting 00, command 00 00.
Media detection by looking for a 1 on bit 0 of the CSR12 control port.
21140 Non-MII transceiver with media 0 (10baseT).
CSR12 control port setting 00, command 00 00.
Media detection by looking for a 1 on bit 0 of the CSR12 control port.
***WARNING***: No MII transceivers found!
Internal autonegotiation state is 'Autonegotiation disabled'.