[tulip] SMC EZ Cardbus 10/100 Problem

[Scott W. Turner]

First,

   Sorry for the confirm post to this board.
  
Next,

   I have a smc ez cardbus 10/100 ethernet card
   and am having trouble getting it to work.

   My setup:

      1) sony vaio 505fx notebook
      2) linux mandrake kernel v2.2.9
      3) built/installed netdriver 2.0
      4) built/installed pcmcia 3.1.15
      5) info from /etc/pcmcia/config:
            1) device "tulip"
               class "network" module "cb_enabler",
                                      "pci-scan",
                                      "cb_shim",
                                      "tulip"
            2) card "SMC EZ 10/100 Fast Ethernet"
               manfid 0x01bf, 0x2220
               bind "tulip"
            3) card "SMC EZ 10/100 Fast Ethernet"
               manfid 0x01bf, 0x2225
               bind "tulip"
      6) when i plug the card into the pc (dongle
         is plugged into a smc hub (port 1) with no other
         ports in use), two high beeps are heard and 
         the utilization 40+ % and collision leds
         come on and stay on constant.  the hub
         port 1 led starts flashing very fast and
         does not stop flashing.
      7) lsmod shows:
            tulip, cb_shim, pci-scan, cb_enabler
      8) the following is my dmesg output:

cs: cb_alloc(bus 32): vendor 0x1011, device 0x0019
ROM image dump:
  image 0: 0x000000-0x0001ff, signature PCIR
cb_shim.c:v1.00 4/15/2000  Donald Becker <becker@scyld.com>
 http://www.scyld.com/linux/drivers.html
tulip.c:v0.92 4/17/2000  Written by Donald Becker <becker@scyld.com>
  http://www.scyld.com/network/tulip.html
Failed to map PCI address 0x0 for device 'Digital DS21143 Tulip'.
cs: cb_config(bus 32)
  fn 0 bar 1: io 0x400-0x47f
  fn 0 bar 2: mem 0x600c0000-0x600c03ff
  fn 0 rom: mem 0x60080000-0x600bffff
cs: cb_enable(bus 32)
  bridge io map 0 (flags 0x21): 0x400-0x47f
  bridge mem map 0 (flags 0x1): 0x60080000-0x600c0fff
Found a Digital DS21143 Tulip at 32/0 address 0x600c0000->0xc4068000 IRQ
9.
Digital DS21143 Tulip at 32/0 command 0x7.
eth0: Digital DS21143 Tulip rev 65 at 0xc4068000, 00:E0:29:5A:AC:7D, IRQ
9.
eth0:  EEPROM default media type Autosense.
eth0:  MII interface PHY 0, setup/reset sequences 2/2 long, capabilities
02 08.
eth0:  Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
eth0: Using media type MII, CSR12 is c6.
eth0:  MII transceiver #1 config 3000 status 7809 advertising 00a1.
eth0:  Advertising 01e1 on PHY 1, previously advertising 00a1.
eth0: Handling power event 1.
eth0: Handling power event 4.
eth0: Unregistering device.
alloc_skb called nonatomically from interrupt c0150c75
cs: cb_disable(bus 32)
cs: cb_release(bus 32)
cs: cb_free(bus 32)

   Can someone help me please.

   I bought the card last week and have just
   1 more week before I can return it w/refund.

   Thanks.      
               

Scott Turner  <><
Marconi Commerce Systems Inc.
Software Engineer       Retail Systems Development
Phone: 336-547-5032     Fax: 336-547-5079
E-mail: scott.turner@marconi.com  (as of  6/5/2000)
E-mail: scott_turner@gilbarco.com (before 6/5/2000)

This document contains confidential information of Marconi Commerce
Systems,Inc. In consideration of the receipt of this document, the recipient
agrees not to reproduce, copy, use or transmit this document and/or the
information contained herein, in purpose except with written permission,
first obtained, of Marconi Commerce Systems, Inc. and further agrees to
surrender the same to Marconi Commerce Systems, Inc. upon demand.