[tulip] Problem with tulip en Mandrake 7.2

[Silvio =?ISO-8859-1?Q?Andr=E9s?= Salazar =?ISO-8859-1?Q?Mart=EDnez?=]

Hi.

I have a Linux Mandrake 7.2 with a "PCI Fast Ethernet DEC 21143 Based" 
according to windows and GadLine CableModem.

In the installation process of Mandrake, it detects my net card and Enet 
button in cablemodem is turns on; but when I run my computer the Enet 
button is turn off.

I read the documentation in
http://www.scyld.com/network/
I downloaded the driver of tulip 
ftp://ftp.scyld.com/pub/network/netdriver-2.1.src.rpm
and nothing, my net card and cable modem aren't functioning.

One aclaration is that the net card is attached to board; my computer is 
a Compaq Presario 5673. While working with windows I don´t have any kind 
of problem.

Else, the net card is detected by kernel.

=========

I attach the results of tulip-diag command:

tulip-diag.c:v2.03 7/31/2000 Donald Becker (becker@scyld.com)
http://www.scyld.com/diag/index.html
Index #1: Found a Digital DS21143 Tulip adapter at 0x2000.
Digital DS21143 Tulip chip registers at 0x2000:
f8a08000 ffffffff ffffffff 07a62800 07a62a00 f4200100 320e0000 f3fe0000
e0000000 ffffcbf8 ffffffff 00000000 000000c6 ffff0000 fff8ffff 8ff70000
Port selection is MII, half-duplex.
Transmit stopped, Receive stopped, half-duplex.
The Rx process state is 'Stopped'.
The Tx process state is 'Waiting for Tx to finish'.
The transmit threshold is 128.
The NWay status register is 000000c6.
Internal autonegotiation state is 'Autonegotiation disabled'.

-e

EEPROM size is 6.
PCI Subsystem IDs, vendor 0e11, device b11e.
CardBus Information Structure at offset 00000000.
Ethernet MAC Station Address 00:50:8B:34:F6:E7.
EEPROM transceiver/media description for the Digital DS21143 Tulip chip.
Leaf node at offset 30, default media type 0800 (Autosense).
  4 transceiver description blocks:
   Media Home-PNA 1Mbps, block type 2, length 6.
    Serial transceiver for Home-PNA 1Mbps (media type 18).
     GP pin direction 080f  GP pin data 0001.
   Media 10baseT, block type 2, length 6.
    Serial transceiver for 10baseT (media type 0).
     GP pin direction 08af  GP pin data 0001.
   Media 10baseT-Full Duplex, block type 2, length 6.
    Serial transceiver for 10baseT-Full Duplex (media type 4).
     GP pin direction 08af  GP pin data 0001.
   Media MII, block type 3, length 17.
    MII interface PHY 0 (media type 11).
    21143 MII initialization sequence is 2 words: 0803 0003.
    21143 MII reset sequence is 0 words:.
     Media capabilities are 7800, advertising 01e1.
     Full-duplex map 5000, Threshold map 1800.
     No MII interrupt.
    No MII transceivers found!
   Internal autonegotiation state is 'Autonegotiation disabled'.

mii-diag
Using the default interface 'eth0'.
Basic registers of MII PHY #32:  1000 7848 0000 0000 0061 0000 0000 0000.
  Basic mode control register 0x1000: Auto-negotiation enabled.
  Basic mode status register 0x7848 ... 7848.
    Link status: not established.

[root@localhost sbin]# mii-diag -v
mii-diag.c:v2.00 4/19/2000  Donald Becker (becker@scyld.com)
  http://www.scyld.com/diag/index.html
Using the default interface 'eth0'.
  MII PHY #32 transceiver registers:
    1000 7848 0000 0000 0061 0000 0000 0000
    0000 0000 0000 0000 0000 0000 0000 0000
    0000 0000 0000 0000 0000 0000 0000 0000
    0000 0000 0000 0000 0000 0000 0000 0000.
  Basic mode control register 0x1000: Auto-negotiation enabled.
  Basic mode status register 0x7848 ... 7848.
    Link status: not established.
    This transceiver is capable of  100baseTx-FD 100baseTx 10baseT-FD 
10baseT.
    Able to perform Auto-negotiation, negotiation not complete.
  MII PHY #32 transceiver registers:
    1000 7848 0000 0000 0061 0000 0000 0000
    0000 0000 0000 0000 0000 0000 0000 0000
    0000 0000 0000 0000 0000 0000 0000 0000
    0000 0000 0000 0000 0000 0000 0000 0000.
  Basic mode control register 0x1000: Auto-negotiation enabled.
  Basic mode status register 0x7848 ... 7848.
    Link status: not established.
    Capable of  100baseTx-FD 100baseTx 10baseT-FD 10baseT.
    Able to perform Auto-negotiation, negotiation not complete.
  This transceiver has no vendor identification.
  I'm advertising 0061: 10baseT-FD 10baseT
    Advertising no additional info pages.
    IEEE 802.3 CSMA/CD protocol.
  Link partner capability is 0000:.
    Negotiation did not complete.
=========

Thanks for your helping.


-- 
=====
Ing. Silvio Andrés Salazar Martínez
e-mail:silas@epm.net.co
Medellín - Colombia