[tulip] Fwd: problems with dec-chip cards
Frank Lingott
f.lingott@cfn.de
Sun, 18 Mar 2001 18:11:24 +0100
Hi,
I have already posted this message about my problem,
but there was no reply.
My server has 2 netcards,
eth0 -> Cogent EM110 / DC21140
eth1 -> DEC DE450TA / DC21041
eth0 is connected to my internal network,
eth1 is connected to my dialup-server via crossover link.
Everything works well with the old Installation(kernel 2.0.35/suse 5.3)
Driver is
tulip.c:v0.89H 5/23/98 becker@cesdis.gsfc.nasa.gov
Now ive installed a new system(suse6.4/kernel2.2.14) on the
second disk.
I configured the network in the same way like my old system,
but eth1 does not work.
I can not reach the dialup server from the server and i cannot
reach the server from the dialup server.
Strange,its the same host !
Is it the driver or the kernel ?
and here some output from the old installation :
/etc/conf.modules
# Aliases - specify your hardware
alias eth0 tulip
alias eth1 tulip
#
options eth0 options=0
options eth1 options=0
#
---------------------------------------------
/etc/hosts
127.0.0.1 localhost
192.168.2.1 machine-1.linuxnet.de machine-1 # my desktop system
192.168.2.2 linuxsystem.linuxnet.de linuxsystem # my server
192.168.2.3 machine-3.linuxnet.de machine-3 # my windoze :-)
192.168.3.1 bardioc.universal.net bardioc # eth1/server
192.168.3.2 ganerc.universal.net ganerc # dialup server
----------------------------------------------
/etc/route.conf
# my personal configurations --------------------------------------
# internal net/first netcard
192.168.2.0 0.0.0.0 255.255.255.0 eth0
#
# loopback
127.0.0.0 0.0.0.0 255.255.255.0 lo
#
#
#
#
#
#
# way to the dialup server/second netcard
#
192.168.3.0 0.0.0.0 255.255.255.0 eth1
#
default 192.168.3.2
#
---------------------------------------------------
output of lsmod
tulip 7 2 (autoclean)
dummy0 1 1 (autoclean)
memstat 1 0
Module Pages Used by
some messages from dmesg/new installation on second hd
Linux version 2.2.14 (root@Pentium.suse.de) (gcc version 2.95.2 19991024 (release)) #1 Mon Mar 13 10:51:48 GMT 2000
Detected 400956037 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 799.54 BogoMIPS
Memory: 322220k/327680k available (1416k kernel code, 416k reserved, 3564k data, 64k init, 0k bigmem)
Dentry hash table entries: 65536 (order 7, 512k)
Buffer cache hash table entries: 524288 (order 9, 2048k)
Page cache hash table entries: 131072 (order 7, 512k)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: L1 I Cache: 32K L1 D Cache: 32K
CPU: AMD AMD-K6(tm) 3D processor
..
..
..
tulip.c:v0.91g-ppc 7/16/99 becker@cesdis.gsfc.nasa.gov
eth0: Digital DS21140 Tulip rev 18 at 0xe400, 00:00:92:96:2C:A7, IRQ 10.
eth0: Old format EEPROM on 'Cogent EM100' board. Using substitute media control info.
eth0: EEPROM default media type Autosense.
eth0: Index #0 - Media 100baseFx (#7) described by a 21140 non-MII (0) block.
eth0: Index #1 - Media 100baseFx-FD (#8) described by a 21140 non-MII (0) block.
eth0: Index #2 - Media 10baseT (#0) described by a 21140 non-MII (0) block.
eth0: Index #3 - Media 10baseT-FD (#4) described by a 21140 non-MII (0) block.
eth0: Index #4 - Media 100baseTx (#3) described by a 21140 non-MII (0) block.
eth0: Index #5 - Media 100baseTx-FD (#5) described by a 21140 non-MII (0) block.
eth1: Digital DC21041 Tulip rev 17 at 0xe800, 00:00:F8:00:EF:C6, IRQ 5.
eth1: 21041 Media table, default media 0000 (10baseT).
eth1: 21041 media #0, 10baseT.
eth1: 21041 media #4, 10baseT-FD.
eth0: Using user-specified media 100baseTx.
eth1: 21143 10baseT link beat good.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de)
nfsd_fh_init : initialized fhcache, entries=512
eth1: 21041 transmit timed out, status fc260000, CSR12 000050c8, CSR13 ffffef01, CSR14 ffffffff, resetting...
eth1: 21143 10mbps sensed media.
exp_do_unexport: 03:48 last use, flushing cache
exp_do_unexport: 03:47 last use, flushing cache
nfsd: terminating on signal 9
nfsd: terminating on signal 9
nfsd: terminating on signal 9
nfsd: terminating on signal 9
nfsd: last server exiting
nfsd_fh_shutdown : freeing 512 fhcache entries.
tulip.c:v0.91g-ppc 7/16/99 becker@cesdis.gsfc.nasa.gov
eth0: Digital DS21140 Tulip rev 18 at 0xe400, 00:00:92:96:2C:A7, IRQ 10.
eth0: Old format EEPROM on 'Cogent EM100' board. Using substitute media control info.
eth0: EEPROM default media type Autosense.
eth0: Index #0 - Media 100baseFx (#7) described by a 21140 non-MII (0) block.
eth0: Index #1 - Media 100baseFx-FD (#8) described by a 21140 non-MII (0) block.
eth0: Index #2 - Media 10baseT (#0) described by a 21140 non-MII (0) block.
eth0: Index #3 - Media 10baseT-FD (#4) described by a 21140 non-MII (0) block.
eth0: Index #4 - Media 100baseTx (#3) described by a 21140 non-MII (0) block.
eth0: Index #5 - Media 100baseTx-FD (#5) described by a 21140 non-MII (0) block.
eth1: Digital DC21041 Tulip rev 17 at 0xe800, 00:00:F8:00:EF:C6, IRQ 5.
eth1: 21041 Media table, default media 0000 (10baseT).
eth1: 21041 media #0, 10baseT.
eth1: 21041 media #4, 10baseT-FD.
eth1: 21143 10baseT link beat good.
lockd_up: no pid, 2 users??
nfsd_fh_init : initialized fhcache, entries=512
eth1: 21041 transmit timed out, status fc260000, CSR12 000050c8, CSR13 ffffef01, CSR14 ffffffff, resetting...
eth1: 21143 10mbps sensed media.
....and
Thanks for your help
Frank
--
"No one said it would be easy"
frank@lugh.de
www.lugh.de