[eepro100] wait_for_cmd_done timeout in 2.4.19-re2-ac2

[Ben Greear]

This is a multi-part message in MIME format.
--------------020307050106070107020400
Content-Type: text/plain; charset=us-ascii; format=flowed
Content-Transfer-Encoding: 7bit

My EEA2 motherboard with eepro100 driver screwed up again today.
This seems to be the same old issue with the eepro100 being
connected to a 10bt hub.  I believe this kernel has all of the
patches from the Sun engineer (sparker), but maybe it doesn't??

The error is: wait_for_cmd_done timeout!

The one good thing is that at least the machine didn't
lock up hard like it used to.

Looks like it's back to e100 time, unfortunately.

eepro100-diag output is attached in case that is useful.l

Thanks,
Ben

-- 
Ben Greear <greearb@candelatech.com>       <Ben_Greear AT excite.com>
President of Candela Technologies Inc      http://www.candelatech.com
ScryMUD:  http://scry.wanfear.com     http://scry.wanfear.com/~greear


--------------020307050106070107020400
Content-Type: text/plain;
 name="foo.txt"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
 filename="foo.txt"

eepro100-diag.c:v2.02 7/19/2000 Donald Becker (becker@scyld.com)
 http://www.scyld.com/diag/index.html
Index #1: Found a Intel i82562 EEPro100 adapter at 0xdf00.
i82557 chip registers at 0xdf00:
  0c000050 0efbb1a0 00000000 00080002 18250021 00000600
  No interrupt sources are pending.
   The transmit unit state is 'Suspended'.
   The receive unit state is 'Ready'.
  This status is normal for an activated but idle interface.
 The Command register has an unprocessed command 0c00(?!).
EEPROM contents, size 64x16:
    00: 0300 c247 d2a6 1a03 0000 0201 4701 0000
  0x08: 0000 0000 49b2 3013 8086 007f ffff ffff
  0x10: ffff ffff ffff ffff ffff ffff ffff ffff
  0x18: ffff ffff ffff ffff ffff ffff ffff ffff
  0x20: ffff ffff ffff ffff ffff ffff ffff ffff
  0x28: ffff ffff ffff ffff ffff ffff ffff ffff
  0x30: 0120 4000 4011 ffff ffff ffff ffff ffff
  0x38: ffff ffff ffff 0000 ffff ffff ffff 43fa
 The EEPROM checksum is correct.
Intel EtherExpress Pro 10/100 EEPROM contents:
  Station address 00:03:47:C2:A6:D2.
  Board assembly 000000-000, Physical connectors present: RJ45
  Primary interface chip i82555 PHY #1.
 MII PHY #1 transceiver registers:
  3100 782d 02a8 0330 05e1 0021 0000 0000
  0000 0000 0000 0000 0000 0000 0000 0000
  2404 0000 0000 0000 0000 0000 0000 0000
  0000 0000 0000 0000 0010 0000 0000 0000.
 Use '-a' or '-aa' to show device registers,
     '-e' to show EEPROM contents, -ee for parsed contents,
  or '-m' or '-mm' to show MII management registers.

--------------020307050106070107020400--