DEC personal station on-board ethernet
Huayong Yang
yang@intersys.com
Sat Dec 19 13:45:34 1998
--=====================_2698169==_
Content-Type: text/plain; charset="us-ascii"
I have an on-board "10/100 BaseT Ethernet twisted pair" on my DEC PII 400i
Personal Station. I use RedHat 5.1 with tulip driver upgraded to 0.90f.
After login, I cannot ping any server using IP address. Apparently the card
is not set up properly. But when I boot it to NT 4.0, I have no problem
with network.
Attached are log files from running dmesg and tulip-diag, and the file
/proc/pci.
Any idea what is wrong? Thanks in advance.
--=====================_2698169==_
Content-Type: text/plain; charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
Content-Disposition: attachment; filename="Proc_pci.log"
PCI devices found:
Bus 0, device 14, function 0:
PCI bridge: DEC Unknown device (rev 2).
Vendor id=3D1011. Device id=3D26.
Medium devsel. Fast back-to-back capable. Master Capable. =
Latency=3D64. Min Gnt=3D4.
Non-prefetchable 32 bit memory at 0x44030300.
I/O at 0x228001f0.
Non-prefetchable 32 bit memory at 0xfff0.
I/O at 0x1fff0.
Bus 2, device 7, function 0:
Ethernet controller: DEC DC21142 (rev 65).
Medium devsel. Fast back-to-back capable. IRQ 9. Master Capable. =
Latency=3D165. Min Gnt=3D20.Max Lat=3D40.
I/O at 0x7c00.
Non-prefetchable 32 bit memory at 0xfd7ff800.
Bus 2, device 6, function 0:
SCSI storage controller: Q Logic ISP1020 (rev 6).
Medium devsel. IRQ 9. Master Capable. Latency=3D64.
I/O at 0x7800.
Non-prefetchable 32 bit memory at 0xfd7fe000.
Bus 0, device 13, function 0:
PCI bridge: DEC DC21152 (rev 3).
Medium devsel. Fast back-to-back capable. Master Capable. =
Latency=3D64. Min Gnt=3D4.
Non-prefetchable 32 bit memory at 0x55020200.
I/O at 0x22807170.
Non-prefetchable 32 bit memory at 0xfd70fd70.
I/O at 0x1fff0.
Bus 0, device 11, function 0:
SCSI storage controller: Adaptec AIC-7881U (rev 0).
Medium devsel. Fast back-to-back capable. IRQ 11. Master Capable. =
Latency=3D64. Min Gnt=3D8.Max Lat=3D8.
I/O at 0xe800.
Non-prefetchable 32 bit memory at 0xfeddf000.
Bus 0, device 9, function 0:
VGA compatible controller: 3Dlabs Unknown device (rev 1).
Vendor id=3D3d3d. Device id=3D9.
Medium devsel. Fast back-to-back capable. IRQ 9. Master Capable. =
Latency=3D64. Min Gnt=3D192.Max Lat=3D192.
Non-prefetchable 32 bit memory at 0xfede0000.
Non-prefetchable 32 bit memory at 0xfd800000.
Non-prefetchable 32 bit memory at 0xfe000000.
Bus 0, device 7, function 3:
Bridge: Intel 82371AB PIIX4 Power Management (rev 2).
Medium devsel. Fast back-to-back capable.
Bus 0, device 7, function 2:
USB Controller: Intel 82371AB PIIX4 (rev 1).
Medium devsel. Fast back-to-back capable. IRQ 9. Master Capable. =
Latency=3D64.
I/O at 0xece0.
Bus 0, device 7, function 1:
IDE interface: Intel 82371AB 430TX PIIX4 (rev 1).
Medium devsel. Fast back-to-back capable. Master Capable. =
Latency=3D64.
I/O at 0xecd0.
Bus 0, device 7, function 0:
ISA bridge: Intel 82371AB PIIX4 (rev 2).
Medium devsel. Fast back-to-back capable. Master Capable. No=
bursts.
Bus 0, device 1, function 0:
PCI bridge: Intel Unknown device (rev 2).
Vendor id=3D8086. Device id=3D7191.
Medium devsel. Master Capable. Latency=3D64. Min Gnt=3D132.
Non-prefetchable 32 bit memory at 0x40010100.
Non-prefetchable 32 bit memory at 0x22a000f0.
Non-prefetchable 32 bit memory at 0xfff0.
Non-prefetchable 32 bit memory at 0xfff0.
Bus 0, device 0, function 0:
Host bridge: Intel Unknown device (rev 2).
Vendor id=3D8086. Device id=3D7190.
Medium devsel. Master Capable. Latency=3D64.
Prefetchable 32 bit memory at 0xf8000000.
--=====================_2698169==_
Content-Type: text/plain; charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
Content-Disposition: attachment; filename="Dmesg.log"
ibios_init : BIOS32 Service Directory entry at 0xfd750
pcibios_init : PCI BIOS revision 2.10 entry at 0xfd966
Probing PCI hardware.
Warning : Unknown PCI device (8086:7190). Please read include/linux/pci.h=
Warning : Unknown PCI device (8086:7191). Please read include/linux/pci.h=
Warning : Unknown PCI device (3d3d:9). Please read include/linux/pci.h=
Warning : Unknown PCI device (1011:26). Please read include/linux/pci.h=
Calibrating delay loop.. ok - 396.49 BogoMIPS
Memory: 63964k/66556k available (736k kernel code, 384k reserved, 1268k=
data)
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: IGMP, ICMP, UDP, TCP
VFS: Diskquotas version dquot_5.6.0 initialized
Checking 386/387 coupling... Ok, fpu using exception 16 error=
reporting.
Checking 'hlt' instruction... Ok.
Linux version 2.0.32 (root@porky.redhat.com) (gcc version 2.7.2.3) #1 Wed=
Nov 19 00:46:45 EST 1997
Starting kswapd v 1.4.2.2
Serial driver version 4.13 with no serial options enabled
tty00 at 0x03f8 (irq =3D 4) is a 16550A
tty01 at 0x02f8 (irq =3D 3) is a 16550A
PS/2 auxiliary pointing device detected -- driver installed.
Real Time Clock Driver v1.07
Ramdisk driver initialized : 16 ramdisks of 4096K size
ide: i82371 PIIX (Triton) on PCI bus 0 function 57
ide0: BM-DMA at 0xecd0-0xecd7
ide1: BM-DMA at 0xecd8-0xecdf
hdc: CD-532E, ATAPI CDROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.35 MAX_MD_DEV=3D4, MAX_REAL=3D8
scsi : 0 hosts.
scsi : detected total.
Partition check:
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
qlogicisp : new isp1020 revision ID (6)
scsi0 : QLogic ISP1020 SCSI on PCI bus 2 device 6 irq 9 base 0x7800
scsi : 1 host.
Vendor: DEC Model: RZ2CC-KA (C) DEC Rev: 4110
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: DEC Model: RZ2DC-KA (C) DEC Rev: 4110
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
SCSI device sda: hdwr sector=3D 512 bytes. Sectors=3D 8380080 [4091 MB] [4.1=
GB]
sda: sda1
SCSI device sdb: hdwr sector=3D 512 bytes. Sectors=3D 17773524 [8678 MB]=
[8.7 GB]
sdb: sdb1 sdb2 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 >
aic7xxx: <Adaptec AHA-294X Ultra SCSI host adapter> at PCI 11
aic7xxx: Warning - detected auto-termination. Please verify driver
detected settings and use manual termination if necessary.
aic7xxx: BIOS enabled, IO Port 0xe800, IO Mem 0xfeddf000, IRQ 11, Revision=
B
aic7xxx: Wide Channel, SCSI ID 7, 16/16 SCBs, QFull 16, QMask 0x1f
scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 4.1/3.2
scsi : 2 hosts.
scsi1: Scanning channel A for devices.
VFS: Mounted root (ext2 filesystem) readonly.
Trying to unmount old root ... okay
Adding Swap: 128484k swap-space (priority -1)
sysctl: ip forwarding off
Swansea University Computer Society IPX 0.34 for NET3.035
IPX Portions Copyright (c) 1995 Caldera, Inc.
Appletalk 0.17 for Linux NET3.035
tulip.c:v0.90f 12/17/98 becker@cesdis.gsfc.nasa.gov
eth0: Digital DS21143 Tulip at 0x7c00, 00 00 f8 7c 25 c6, IRQ 9.
eth0: EEPROM default media type Autosense.
eth0: Index #0 - Media 10baseT (#0) described by a 21142 Serial PHY (2)=
block.
eth0: Index #1 - Media 10baseT-FD (#4) described by a 21142 Serial PHY (2)=
block.
eth0: Index #2 - Media 100baseTx (#3) described by a 21143 SYM PHY (4)=
block.
eth0: Index #3 - Media 100baseTx-FD (#5) described by a 21143 SYM PHY (4)=
block.
eth0: Index #4 - Media AUI (#2) described by a 21142 Serial PHY (2)=
block.
eth0: Index #5 - Media 10base2 (#1) described by a 21142 Serial PHY (2)=
block.
VFS: Disk change detected on device 02:10
--=====================_2698169==_
Content-Type: text/plain; charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
Content-Disposition: attachment; filename="Diag.log"
tulip-diag.c:v1.06 9/18/98 Donald Becker (becker@cesdis.gsfc.nasa.gov)
Index #1: Found a Digital DS21143 Tulip adapter at 0x7c00.
Digital DS21143 Tulip Tulip chip registers at 0x7c00:
f8000000 ffffffff ffffffff 00bec100 00beb040 f0000000 32000040 f3fe0000
e0000000 fff583ff ffffffff 00000000 000000c6 ffff0000 ffffffff 8ff00000
The Rx process state is 'Stopped'.
The Tx process state is 'Stopped'.
Transmit stopped, Receive stopped, half-duplex.
The transmit threshold is 72.
Port selection is 10mpbs-serial, half-duplex.
EEPROM contents:
0000 0000 0000 0000 0000 0000 0000 0000
0000 0104 0000 7cf8 c625 1e00 0000 0800
8606 0002 08b0 00b0 0286 b004 b008 8800
0304 08b0 00b0 8061 0488 b005 b008 6100
8680 0202 08b0 00b0 0286 b001 b008 0000
0000 0000 0000 0000 0000 0000 0000 4050
0000 0000 0000 0000 7cf8 c625 00a1 0000
0000 0000 0000 0000 0000 0000 0000 00a5
ID CRC 0xe3 (vs. 00), complete CRC 9befbaea.
EEPROM transceiver/media description for the Digital DS21143 Tulip=
chip.
Leaf node at offset 30, default media type 0800 (Autosense).
6 transceiver description blocks:
Media 10baseT, block type 2.
Serial transceiver for 10baseT (media type 0).
GP pin direction 08b0 GP pin data 00b0.
Media 10baseT-Full Duplex, block type 2.
Serial transceiver for 10baseT-Full Duplex (media type 4).
GP pin direction 08b0 GP pin data 00b0.
Media 100baseTx, block type 4.
SYM transceiver for 100baseTx (media type 3).
GP pin direction 08b0 GP pin data 00b0.
No media detection indication (command 80 61).
Media 100baseTx Full Duplex, block type 4.
SYM transceiver for 100baseTx Full Duplex (media type 5).
GP pin direction 08b0 GP pin data 00b0.
No media detection indication (command 80 61).
Media AUI, block type 2.
Serial transceiver for AUI (media type 2).
GP pin direction 08b0 GP pin data 00b0.
Media 10base2, block type 2.
Serial transceiver for 10base2 (media type 1).
GP pin direction 08b0 GP pin data 00b0.
***WARNING***: No MII transceivers found!
Internal autonegotiation state is 'Autonegotiation disabled'.
--=====================_2698169==_
Content-Type: text/plain; charset="us-ascii"
--
Huayong Yang
InterSystems Corporation, 1 Memorial Drive, Cambridge, MA 02142
617-577-3631, yang@intersys.com
--=====================_2698169==_--