0.90k & Linksys Cardbus still no go

[Chris Chiappa]

Latest driver still doesn't work with the Linksys cardbus card here.  dmesg
and tulip-diag output is attached.  Trying to increase tulip_debug led to
the screen being flooded with messages I couldn't write down (and the
Magic-SysRq-Sync didn't get into the log files).  I saw a few oopses fly by
as well.

Detected as:
Linux PCMCIA Card Services 3.0.8
  kernel build: 2.2.0-pre7 #1 Thu Jan 14 18:52:34 EST 1999
    options:  [pci] [cardbus] [apm]
	 Intel PCIC probe: 
	   Toshiba ToPIC95-B PCI-to-CardBus at bus 0 slot 11, mem 0x68000000, 2
sockets
    host opts [0]: [slot 0xf0] [ccr 0x10] [cdr 0x86] [rcr 0x02] [no pci irq]
[lat 168/176] [bus 20/20]
    host opts [1]: [slot 0xf0] [ccr 0x10] [cdr 0x86] [rcr 0x02] [no pci irq]
[lat 168/176] [bus 21/21]
    ISA irqs (default) = 3,4,5,7,9,10 polling interval = 1000 ms
cs: IO port probe 0x0a00-0x0aff: clean.
cs: cb_config(bus 20): vendor 0x1011, device 0x0019
  fn 0 bar 1: io 0xa00-0xa7f
  fn 0 bar 2: mem 0xa00c0000-0xa00c03ff
  fn 0 rom: mem 0xa0080000-0xa00bffff
cs: cb_enable(bus 20)
  bridge io map 0 (flags 0x21): 0xa00-0xa7f
  bridge mem map 0 (flags 0x1): 0xa0080000-0xa00c0fff
tulip_attach(bus 20, function 0)
tulip.c:v0.90k 2/1/99 becker@cesdis.gsfc.nasa.gov
eth0: Digital DS21143 Tulip rev 65 at 0xa00, 00 e0 98 04 89 b4, IRQ 3.
eth0:  EEPROM default media type Autosense.
eth0:  Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
eth0:  MII transceiver #0 config 3000 status 7809 advertising 01e1.
Subsequently causes:
eth0: Tx hung, 9 vs. 0.
eth0: Tx hung, 15 vs. 0.
eth0: Tx hung, 15 vs. 0.
eth0: Tx hung, 15 vs. 0.
eth0: Tx hung, 15 vs. 0.
eth0: Tx hung, 15 vs. 0.

tulip-diag reports:
tulip-diag.c:v1.06 9/18/98 Donald Becker (becker@cesdis.gsfc.nasa.gov)
Digital DC21040 Tulip Tulip chip registers at 0xa00:
  fa008000 ffffffff ffffffff 00fff810 00fffa10 f02001c6 b20e0000 f3fe0000
  e0000000 fffd83ff ffffffff 00000000 000000c6 ffff0000 fff80000 8ff90008
 The Rx process state is 'Stopped'.
 The Tx process state is 'Waiting for Tx to finish'.
Transmit stopped, Receive stopped, half-duplex.
 The transmit threshold is 128.
 Port selection is MII, half-duplex.
 MII PHY found at address 0, status 0x782d.
 MII PHY #0 transceiver registers:
   3000 782d 0040 6212 01e1 0021 0000 0000
	0000 0000 0000 0000 0000 0000 0000 0000
	1000 0000 0000 0000 0000 0000 0200 0000
	003c 8006 0f00 ff00 002c 0000 0080 000b.

-- 

+------- ---  -- --  -
| griffon@snurgle.N0-SPAM.org   /   My opinions represent snurgle.org :
! Unspoilt by progress         /    http://www.snurgle.org/~griffon   |
                                                 -  -- --  --- -------+